Is the TE-NT screw connection tee, carbon steel, compatible with NPT threads sealed using Teflon tape or anaerobic sealant while maintaining the 2.5:1 safety factor?

Yes. The TE-NT screw connection tee, carbon steel (24Â° DIN 2353 socket with external metric thread and external NPT thread) is specified for sealing on the NPT thread using Teflon tape or anaerobic sealant and is rated with a safety factor of 2.5:1. When installed correctly per DIN 2353 guidance and manufacturer torque/specifications, using appropriate thread sealant (PTFE tape or compatible anaerobic compound) will maintain the specified 2.5:1 safety factor. Ensure you use the correct sealant quantity, proper thread engagement, and the matching series (L or S) and material finish (galvanized carbon steel) for the intended pressure and service conditions; follow assembly torque and inspection procedures to preserve the rating.

Does the TE-NT screw connection tee, carbon steel, maintain pressure ratings when using external NPT threads sealed with Teflon tape or anaerobic sealant?

Yes. The TE-NT screw connection tee, carbon steel (24Â° DIN 2353 socket with external metric thread and external NPT thread) is specified for sealing the NPT thread with Teflon tape or anaerobic sealant, and with a stated safety factor of 2.5:1 it is intended to retain rated pressure when assembled correctly. To ensure rated performance: use the correct sealing method (sufficient PTFE tape or compatible anaerobic sealant), follow DIN 2353 assembly practices and recommended torque, inspect threads for damage, and use the appropriate series (L or S) for the pressure class required. Improper sealing, insufficient torque, damaged threads or mismatched materials can compromise the pressure rating.

Can TE-NT screw connection tee, carbon steel, tolerate mixed-thread sealing (metric + NPT) with Teflon or anaerobic sealant?

Yes. TE-NT screw connection tee, carbon steel (DIN 2353) can tolerate mixed-thread sealing (metric external + NPT external) using thread sealant such as PTFE (Teflon) tape or an anaerobic thread sealant, with important caveats: - Design intent: The TE-NT is a 24Â° DIN 2353 socket (cone) fitting that seals primarily by the 24Â° cone face when assembled into the corresponding DIN 2353 compression/union components. The external metric and external NPT threads are provided for mechanical engagement and, where specified, thread sealing. The product description explicitly notes âseal on the thread â with Teflon tape or anaerobic sealant,â so thread sealing is an accepted practice for these external threads. - Mixed-thread use: Combining metric external and NPT external threads on the same fitting is mechanically possible only when mating components are designed to accept those specific threads. NPT is a tapered pipe thread that seals by thread deformation; metric external threads are parallel and normally rely on the cone seal or a thread sealant. If you mate the NPT external thread to a proper NPT female port and the metric external thread to a matching metric female port (or vice versa per the intended catalog configuration), you may use a thread sealant on the threaded joint. Do NOT attempt to mate metric threads to NPT female threads or chop/match incompatible thread forms. that will leak and damage threads. - Sealant choice & application: PTFE tape and anaerobic (liquid) thread sealants are both acceptable per the fitting description. Use appropriate PTFE tape (gas/fluid-rated, correct wrap direction, thin/wrap count) or an anaerobic product compatible with carbon steel and the fluid media and temperature. Apply following manufacturer instructions and avoid excess that can contaminate the system. - Safety & ratings: The fitting has a safety factor of 2.5:1 and is offered in light (L) and heavy (S) series; do not exceed the rated pressure/temperature for the chosen series and material. Ensure the mating parts and the sealantâs pressure/temperature/chemical limits are compatible. - Best practice: Use the 24Â° cone assembly where possible for primary sealing per DIN 2353, and use thread sealant only for threaded joints as intended. Inspect threads, use proper torque, and ensure correct thread type matching (metric-to-metric, NPT-to-NPT). When in doubt, consult the fitting manufacturer or a hydraulics engineer for your specific application and media. Conclusion: Yes, TE-NT screw connection tee, carbon steel can be sealed with Teflon tape or anaerobic sealant on the threads when properly matched to the correct female thread types and used within rated limits; do not mix incompatible thread forms.

TE-NT screw connection tee, carbon steel

Additional information

Material	CS – steel (cast iron)

DIN 2353 screw-in tee fitting, type TE-NT: 24° DIN 2353 socket with external metric thread and external NPT thread (seal on the thread – with Teflon tape or anaerobic sealant). Safety factor 2.5:1. Available as: L (light series), S (heavy series). Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HD-TE-06L-NT-02	DIN 2353 fitting TE 6L 1/8" NPT	-	315	In stock	Enquiry
HD-TE-06S-NT-04	DIN 2353 fitting TE 6S 1/4" NPT	-	630	In stock	Enquiry
HD-TE-08L-NT-04	DIN 2353 fitting TE 8L 1/4" NPT	-	315	In stock	Enquiry
HD-TE-08S-NT-04	DIN 2353 TE 8S 1/4" NPT fitting	-	630	In stock	Enquiry
HD-TE-10L-NT-04	DIN 2353 fitting TE 10L 1/4" NPT	-	315	In stock	Enquiry
HD-TE-10S-NT-06	DIN 2353 fitting TE 10S 3/8" NPT	-	630	In stock	Enquiry
HD-TE-12L-NT-06	DIN 2353 fitting TE 12L 3/8" NPT	-	315	In stock	Enquiry
HD-TE-12S-NT-06	DIN 2353 TE 12S 3/8" NPT fitting	-	630	In stock	Enquiry
HD-TE-14S-NT-08	DIN 2353 TE 14S 1/2" NPT fitting	-	630	In stock	Enquiry
HD-TE-15L-NT-08	DIN 2353 fitting TE 15L 1/2" NPT	-	315	In stock	Enquiry
HD-TE-16S-NT-08	DIN 2353 TE 16S 1/2" NPT fitting	-	400	In stock	Enquiry
HD-TE-18L-NT-08	DIN 2353 fitting TE 18L 1/2" NPT	-	315	In stock	Enquiry
HD-TE-20S-NT-12	DIN 2353 fitting TE 20S 3/4" NPT	-	400	In stock	Enquiry
HD-TE-22L-NT-12	DIN 2353 fitting TE 22L 3/4" NPT	-	160	In stock	Enquiry
HD-TE-25S-NT-16	DIN 2353 fitting TE 25S 1" NPT	-	400	In stock	Enquiry
HD-TE-28L-NT-16	DIN 2353 fitting TE 28L 1" NPT	-	160	In stock	Enquiry
HD-TE-30S-NT-20	DIN 2353 fitting TE 30S 1.1/4" NPT	-	400	In stock	Enquiry
HD-TE-35L-NT-20	DIN 2353 fitting TE 35L 1.1/4" NPT	-	160	In stock	Enquiry
HD-TE-38S-NT-24	DIN 2353 fitting TE 38S 1.1/2" NPT	-	315	In stock	Enquiry
HD-TE-42L-NT-24	DIN 2353 fitting TE 42L 1.1/2" NPT	-	160	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

DIN 2353 screw-in tee fitting, type TE-NT: 24° DIN 2353 socket with external metric thread and external NPT thread (seal on the thread – with Teflon tape or anaerobic sealant). Safety factor 2.5:1. Available as: L (light series), S (heavy series). Material: carbon steel, galvanized.