Can the Insulated hot water gun, stainless steel, AKBO, red be used safely with hot water up to +95Â°C and what precautions are required?

Yes . the Insulated hot water gun, stainless steel, AKBO, red is rated for operation up to +95Â°C, but safe use requires strict precautions. Precautions: - Temperature limit: do not exceed +95Â°C. Continuous use at or near this limit increases wear on seals and rubber parts. - Pressure: keep pressure â¤24 bar. Ensure your system pressure is within the 1/2" BSP connection and gun specification. - Seals and materials: Viton seals and EPDM rubber covers are compatible with hot water, but prolonged exposure to high temperature can reduce lifetime; inspect seals and rubber regularly for cracks, hardening or leaks. - Insulation: use the insulated trigger and handle to avoid burns; do not touch metal parts that may become hot. - Flow and spray: designed for up to 75 l/min. Ensure your supply matches this to avoid turbulence or cavitation that could damage components. - Connection and fittings: secure 1/2" BSP connection properly; use appropriate thread sealant and torque to prevent leaks. - Safety checks: before each use, check for leaks, damaged insulation, or worn seals. Replace damaged parts immediately. - Ventilation and splash protection: wear PPE (gloves, eye protection, protective clothing) to guard against hot-water spray and scalding. - Storage and cooldown: allow the gun to cool before maintenance or storage to prevent thermal damage to seals and covers. - Manufacturer guidance: follow any additional manufacturer maintenance and replacement schedules for EPDM and Viton parts. Following these precautions will help ensure safe, reliable operation of the Insulated hot water gun, stainless steel, AKBO, red at temperatures up to +95Â°C.

Is the Insulated hot water gun, stainless steel, AKBO, red compatible with 24 bar pressure and 1/2" BSP connections for hot water use?

Yes. The Insulated hot water gun, stainless steel, AKBO, red is compatible: it has a 1/2" BSP connection and a working pressure of 24 bar. It is constructed from stainless steel with an insulated trigger, EPDM rubber covers and Viton seals, and is rated for hot water use up to +95Â°C-however, use with hot water requires special caution as noted.

Does the Insulated hot water gun, stainless steel, AKBO, red require special maintenance after use with hot water up to +95Â°C?

Yes. After using the Insulated hot water gun, stainless steel, AKBO, red with hot water up to +95Â°C you should perform special maintenance to preserve safety and longevity: - Cool down: Allow the gun and connected hose to cool to a safe temperature before handling or storing. Avoid thermal shock to seals and covers. - Rinse/flush: Flush the gun with clean, lukewarm water to remove deposits, detergents or abrasive particles that could damage EPDM covers or Viton seals. - Inspect seals and covers: Check Viton seals and EPDM rubber covers for swelling, cracking or other deterioration caused by heat or chemicals. Replace any damaged parts. - Dry and ventilate: Drain residual water and let the gun air-dry to prevent corrosion, especially around stainless-steel joints and the 1/2" BSP connection. - Lubricate if specified: If the manufacturer recommends lubrication for moving parts or seals, use only compatible lubricants (Viton/EPDM-safe). - Pressure check: Before next use, verify the gun and connections are intact and rated for working pressure (24 bar). - Chemical caution: Viton is chemically resistant, EPDM less soâif hot water contained chemicals, follow specific cleaning and part-replacement guidance from the manufacturer. - Storage: Store in a cool, dry place away from direct sunlight and chemicals that could degrade rubber parts. Following these steps minimizes wear from high operating temperature (up to +95Â°C) and helps maintain safe operation and the specified flow/pressure performance.

Insulated hot water gun, stainless steel, AKBO, red

All products, Low-pressure water spray guns/

Additional information

Hot water gun AKBO. Made of stainless steel, insulated trigger, EPDM rubber covers, Viton seals. Use with hot water requires special caution. Connection: 1/2″ BSP. Working pressure: 24 bar. Flow rate: 75 l/min. Operating temperature: up to +95°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
AK-RHP01-R	Hot water gun AKBO, GW 1/2" BSP, insulated, AISI 316, red	-	24	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Hot water gun AKBO. Made of stainless steel, insulated trigger, EPDM rubber covers, Viton seals. Use with hot water requires special caution. Connection: 1/2″ BSP. Working pressure: 24 bar. Flow rate: 75 l/min. Operating temperature: up to +95°C.