Is the Jamming ring D, carbon steel, zinc-nickel compatible with 24Â° socket DIN 2353 LL and L/S series fittings?

Yes. The Jamming ring D, carbon steel, zinc-nickel is intended for 24Â° socket DIN 2353 connections and is available for both LL (very light) and L/S (light/heavy) series fittings. Its material (carbon steel) and zincânickel surface coating (6â10 Âµm, high corrosion resistance) match the described application, so it is compatible with 24Â° socket DIN 2353 LL and L/S series fittings.

Does the Jamming ring D, carbon steel, zinc-nickel require special installation tools for 24Â° socket DIN 2353 LL and L/S fittings?

No, the Jamming ring D, carbon steel, zinc-nickel does not require special installation tools for 24Â° socket DIN 2353 LL and L/S fittings. It is designed for standard assembly with those fittings (LL - very light series, L/S - light/heavy series) and the zincânickel coating and carbon steel material do not change the usual installation procedure. Use the normal tools and torque specifications recommended for 24Â° DIN 2353 connections.

Can Jamming ring D, carbon steel, zinc-nickel withstand hydraulic fluid exposure and pressure cycles in 24Â° socket DIN 2353 LL/L/S fittings?

Yes. Jamming ring D, carbon steel, zinc-nickel can withstand hydraulic fluid exposure and pressure cycles in 24Â° socket DIN 2353 LL/L/S fittings for typical hydraulic applications. Rationale: - Material and coating: carbon steel base provides required mechanical strength for repeated pressure cycles; the zinc-nickel coating (6â10 Âµm) offers very high corrosion resistance (tested up to ~720 hours in salt spray), protecting the steel from fluid-induced corrosion and environmental attack. - Compatibility with hydraulic fluids: zinc-nickel coatings are broadly compatible with common hydraulic oils and additives; they prevent direct steel exposure and reduce risk of galvanic or chemical degradation under normal service conditions. - Design and series: Jamming ring D is specified for 24Â° socket DIN 2353 connections in LL (very light) and L/S (light/heavy) series, meaning the component is intended for those fitting types and their respective pressure classes and cycle loads. Limitations and recommendations: - Ensure the specific hydraulic fluid and any aggressive additives or contamination are compatible with zinc-nickel and carbon steel; some specialty fluids or high-moisture/acidic conditions may require additional verification. - Confirm the operating pressures and cycle frequencies against the LL or L/S series ratings and the overall DIN 2353 assembly specifications. - Inspect for coating damage during assembly (scratches or nicks can expose steel) and follow recommended torque/installation procedures to maintain sealing and ring integrity. Conclusion: For standard hydraulic oils and within the rated pressure/cycle classes of DIN 2353 LL or L/S fittings, Jamming ring D, carbon steel, zinc-nickel is suitable for exposure to hydraulic fluid and pressure cycling.

Cutting ring D, carbon steel, zinc-nickel

Additional information

Standard length [m]	60

Cutting ring for socket 24° fittings DIN 2353. Available as: LL (extra-light series) and L/S (series light/heavy), without a designation in the index code. Surface coated with zinc-nickel with a layer thickness of 6-10 µm, which offers very high corrosion resistance (up to 720 hours without corrosion in a salt spray chamber). Material: carbon steel, zinc-nickel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HD-D-04LL-CN	Cutting ring 4 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-06-CN	Cutting ring 6 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-06LL-CN	Cutting ring 6 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-08-CN	Cutting ring 8 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-08LL-CN	Cutting ring 8 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-10-CN	Cutting ring 10 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-12-CN	Cutting ring 12 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-14-CN	Cutting ring 14 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-15-CN	Cutting ring 15 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-16-CN	Cutting ring 16 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-18-CN	Cutting ring 18 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-20-CN	Cutting ring 20 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-22-CN	Cutting ring 22 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-25-CN	Cutting ring 25 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-28-CN	Cutting ring 28 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-30-CN	Cutting ring 30 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-35-CN	Cutting ring 35 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-38-CN	Cutting ring 38 mm, Zn-Ni	-	-	In stock	Enquiry
HD-D-42-CN	Cutting ring 42 mm, Zn-Ni	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Cutting ring for socket 24° fittings DIN 2353. Available as: LL (extra-light series) and L/S (series light/heavy), without a designation in the index code. Surface coated with zinc-nickel with a layer thickness of 6-10 µm, which offers very high corrosion resistance (up to 720 hours without corrosion in a salt spray chamber). Material: carbon steel, zinc-nickel.