How do I select the correct filtration degree and condensate discharge option for the Compressed air preparation unit F+L 100 - 200 - 300, SKILLAIRÂ® series?

To select the correct filtration degree and condensate discharge for the Compressed air preparation unit F+L 100 - 200 - 300, SKILLAIRÂ® series, follow these rules: - Filtration degree: choose 5 Âµm for fine filtration when sensitive pneumatic equipment or precision tools require clean air; 20 Âµm for general-purpose industrial uses; 50 Âµm where coarse filtration is acceptable and higher particulate load is expected. - Condensate discharge: choose manual if infrequent drainage and low condensate volume are acceptable; semi-automatic (RMSA) for reduced operator intervention and moderate condensate; automatic (SAC, RA) where continuous unattended operation and reliable condensate removal are required. - Match unit size (100, 200, 300) to nominal flow (1200â4500 l/min at 6 bar, Îp=1 bar) and ensure supply pressure (up to 15 bar) and connection (BSP 1/4"â1") suit your system.

Can the Compressed air preparation unit F+L 100 - 200 - 300, SKILLAIRÂ® series operate continuously at 15 bar without reduced service life?

The Compressed air preparation unit F+L 100 - 200 - 300, SKILLAIRÂ® series is rated for a supply pressure up to 15 bar (depending on size and type of discharge). Operating at that maximum pressure is within the stated specification; however continuous operation at 15 bar may affect service life depending on specific size, discharge type and actual operating conditions (temperature, condensate management, contamination level and flow). Key points to ensure no premature wear: - Verify the exact model/size and discharge type support continuous 15 bar operation (specification varies by size/type). - Maintain proper filtration (choose correct 5 Âµm/20 Âµm/50 Âµm element) to minimize abrasive particles. - Ensure correct condensate discharge method (automatic preferred) and regular maintenance to prevent moisture-related wear. - Keep operating temperature â¤ +50Â°C and nominal flow within rated range (1200â4500 l/min at 6 bar Îp = 1 bar; higher pressures change flow dynamics). - Follow manufacturer maintenance intervals and use recommended lubricator settings/oil to avoid internal component stress. Conclusion: Technically the unit can operate at up to 15 bar as specified, but continuous operation at that pressure without reduced service life depends on choosing the correct size/type, strict maintenance, proper filtration and condensate control. For definitive assurance, consult the manufacturerâs detailed data sheet or technical support for the specific model.

Compressed air preparation unit F+L 100 – 200 – 300, SKILLAIR® series

Q: What maintenance interval is recommended for the Compressed air preparation unit F+L 100 - 200 - 300, SKILLAIRÂ® series to ensure optimal filtration and lubrication?

For optimal filtration and lubrication of the Compressed air preparation unit F+L 100 - 200 - 300, SKILLAIRÂ® series, perform regular maintenance at least every 3 months under normal operating conditions. Key actions each interval: - Inspect and clean or replace filter elements (5 Âµm, 20 Âµm, 50 Âµm) if contaminated. - Drain condensate from bowls; operate manual/semi-automatic (RMSA) drains as required and verify automatic drains (SAC, RA) function. - Check lubricator oil level and refill with recommended oil; adjust oil feed rate if necessary. - Inspect seals, connections (BSP 1/4" to 1"), and bowl integrity for damage or leaks. - Verify unit performance at operating conditions (up to 15 bar, up to +50Â°C) and nominal flow range (1200â4500 l/min at 6 bar, Îp = 1 bar). Increase frequency (monthly) in heavy-duty, dirty, or high-condensate environments, or after process upsets. Replace components immediately if performance degrades.

Air preparation elements (FRL), All products/

Compressed air preparation unit F+L 100 - 200 - 300, SKILLAIR® series

Additional information

Maximum operating temperature [°C]	50
Standard length [m]	10, 15, 30, 60/ 120

The F + L set of the SKILLAIR® series with a high degree of reliability consists of an air filter and a lubricator. The purpose of the set is to purify the air supplied by the compressor and to lubricate with an oil mist. Size: 100, 200, 300. Supply pressure: up to 15 bar, depending on size and type of discharge. Filtration degree: 5 µm, 20 µm, 50 µm. Connection: BSP 1/4″ to 1″. Condensate discharge: manual/semi-automatic (RMSA), automatic (SAC, RA). Operating temperature: up to +50°C. Nominal flow: from 1200 to 4500 l/min (at an inlet pressure of 6 bar Δp = 1 bar), depending on size.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-3285001	F+L Set 100 1/4 5 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3285002	F+L Set 100 1/4 20 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3285003	F+L Set 100 1/4 50 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3285101	F+L Set 100 1/4 5 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3285102	F+L Set 100 1/4 20 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3285103	F+L Set 100 1/4 50 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3385001	F+L Set 100 3/8 5 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3385002	F+L Set 100 3/8 20 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3385003	F+L Set 100 3/8 50 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3385101	F+L Set 100 3/8 5 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3385102	F+L Set 100 3/8 20 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3385103	F+L Set 100 3/8 50 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3485001	Set F+L 200 1/4 5 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3485002	F+L Set 200 1/4 20 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3485003	F+L Set 200 1/4 50 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3485101	F+L Set 200 1/4 5 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3485102	F+L Set 200 1/4 20 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3485103	F+L Set 200 1/4 50 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3585001	F+L Set 200 3/8 5 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3585002	F+L Set 200 3/8 20 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3585003	F+L Set 200 3/8 50 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3585101	F+L Set 200 3/8 5 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3585102	F+L Set 200 3/8 20 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3585103	F+L Set 200 3/8 50 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3685001	F+L Set 200 1/2 5 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3685002	F+L Set 200 1/2 20 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3685003	F+L Set 200 1/2 50 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-3685101	F+L Set 200 1/2 5 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3685102	F+L Set 200 1/2 20 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-3685103	F+L Set 200 1/2 50 SAC (SKILLAIR)	-	-	In stock	Enquiry
MW-4485001	F+L Set 300 1/2 5 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-4485002	F+L 300 1/2 20 RMSA (SKILLAIR) set	-	-	In stock	Enquiry
MW-4485003	F+L Set 300 1/2 50 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-4485004	Set F+L 300 1/2 5 RA (SKILLAIR)	-	-	In stock	Enquiry
MW-4485005	F+L 300 1/2 20 RA (SKILLAIR) set	-	-	In stock	Enquiry
MW-4485006	F+L Set 300 1/2 50 RA (SKILLAIR)	-	-	In stock	Enquiry
MW-4585001	F+L 300 3/4 5 RMSA (SKILLAIR) Set	-	-	In stock	Enquiry
MW-4585002	F+L 300 3/4 20 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-4585003	F+L 300 3/4 50 RMSA (SKILLAIR) Set	-	-	In stock	Enquiry
MW-4585004	F+L 300 3/4 5 RA (SKILLAIR) Set	-	-	In stock	Enquiry
MW-4585005	F+L 300 3/4 20 RA (SKILLAIR) set	-	-	In stock	Enquiry
MW-4585006	F+L 300 3/4 50 RA (SKILLAIR) set	-	-	In stock	Enquiry
MW-4685001	F+L Set 300 1 5 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-4685002	F+L 300 1 20 RMSA (SKILLAIR) Set	-	-	In stock	Enquiry
MW-4685003	F+L Set 300 1 50 RMSA (SKILLAIR)	-	-	In stock	Enquiry
MW-4685004	F+L 300 1 5 RA (SKILLAIR) Set	-	-	In stock	Enquiry
MW-4685005	F+L Set 300 1 20 RA (SKILLAIR)	-	-	In stock	Enquiry
MW-4685006	F+L 300 1 50 RA (SKILLAIR) Set	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

The F + L set of the SKILLAIR® series with a high degree of reliability consists of an air filter and a lubricator. The purpose of the set is to purify the air supplied by the compressor and to lubricate with an oil mist. Size: 100, 200, 300. Supply pressure: up to 15 bar, depending on size and type of discharge. Filtration degree: 5 µm, 20 µm, 50 µm. Connection: BSP 1/4″ to 1″. Condensate discharge: manual/semi-automatic (RMSA), automatic (SAC, RA). Operating temperature: up to +50°C. Nominal flow: from 1200 to 4500 l/min (at an inlet pressure of 6 bar Δp = 1 bar), depending on size.