Is the SNAP-TITE quick connect plug with GW BSP without valve, carbon steel, H series suitable for hydraulic oil up to 759 bar and -35Â°C to +120Â°C?

Yes. The SNAP-TITE quick connect plug with GW BSP without valve, carbon steel, H series is suitable for hydraulic oil within the stated limits: it is specified for hydraulic power (hydraulic oil), constructed of carbon steel (galvanized) with NBR sealing, rated for working pressures up to 759 bar (size-dependent) with a 2:1 safety factor, and an operating temperature range of -35Â°C to +120Â°C. Ensure you select the correct coupling size for your maximum pressure and confirm NBR compatibility with your specific hydraulic oil and any additives; if oil or additives fall outside NBR compatibility or if temperatures/pressures exceed the listed limits, choose appropriate materials/seals accordingly.

Can SNAP-TITE quick connect plug with GW BSP without valve, carbon steel, H series be used with steam and chemicals at specified temps and pressures?

SNAP-TITE quick connect plug with GW BSP without valve, carbon steel, H series can be used with steam and chemicals only if the materials and seals are compatible with those media and temperatures. Standard configuration: carbon steel (galvanized) with NBR seals, operating range â35Â°C to +120Â°C, working pressure up to 759 bar (size-dependent), safety factor 2:1. NBR is generally unsuitable for hot steam and many aggressive chemicals; carbon steel may corrode with some chemicals or high-temperature steam. For steam and aggressive chemicals at elevated temperature/pressure, select appropriate seal material (e.g., Viton, EPDM, PTFE) and verify carbon steel compatibility or use stainless steel. Confirm required pressure/temperature against coupling size rating and consult manufacturer or MILâCâ51234 conformity before service.

Can SNAP-TITE quick connect plug with GW BSP without valve, carbon steel, H series be used with fuels and gases at specified pressures?

Yes. SNAP-TITE quick connect plug with GW BSP without valve, carbon steel, H series can be used with fuels and gases at the specified pressures, provided the following conditions are met: - Working pressure: The product is rated up to 759 bar (size-dependent) with a 2:1 safety factor. Ensure the specific coupling size you choose supports the actual system pressure for the fuel or gas application. - Material compatibility: The coupling body is carbon steel, galvanized. Confirm carbon steel and its plating are compatible with the specific fuel or gas and any additives present; some aggressive fuels or gases may require stainless steel or alternative finishes. - Sealing: Standard sealing is NBR (nitrile rubber). NBR is compatible with many hydrocarbons (common fuels and oils) but has limitations with certain fuels, biofuels (high ethanol/biodiesel content), and some gases/chemicals. Verify NBR compatibility with the exact fluid or gas and operating temperature. If incompatible, select a different seal material suitable for the service. - Temperature range: -35Â°C to +120Â°C. Confirm the operating temperature of the fuel or gas service stays within this range to maintain seal integrity and material performance. - Flow/pressure drop: Flow data is provided for a 3 bar pressure drop; verify flow requirements for your system and ensure acceptable performance at the intended pressures. - Standards: Meets MIL-C-51234; use where this standard is acceptable. Conclusion: Technically suitable for many fuels and gases at the stated pressures if the coupling size supports the pressure and both carbon steel plating and NBR seals are chemically and thermally compatible with the specific fuel/gas. If any compatibility concern exists, choose appropriate materials (e.g., stainless steel body, FKM or EPDM seals) before use.

SNAP-TITE quick connect plug with GW BSP without valve, carbon steel, H series

All products, Hydraulic quick couplings/

Additional information

Material	CS – steel (cast iron)

SNAP-TITE quick coupling plug with internal BSP thread, American-made, without valve. Application: hydraulic power (hydraulic oil), industrial (water, steam, fuels and oils, gases, chemicals). Depending on the application, the appropriate material for the coupling and sealing must be selected. Standard: MIL-C-51234. Working pressure: up to 759 bar (depending on the size of the quick coupling), safety factor 2:1. Material: carbon steel, galvanized. Sealing: NBR. Operating temperature: from -35°C to +120°C. Flow has been provided for a pressure drop of 3 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
SN-PHN12-12RP	H plug 3/4", G 3/4" BSP, without valve	-	621	In stock	Enquiry
SN-PHN16-16RP	H plug 1", GW 1" BSP, without valve	-	414	In stock	Enquiry
SN-PHN4-4RP	Plug H 1/4", G 1/4" BSP, without valve	-	759	In stock	Enquiry
SN-PHN6-6RP	H plug 3/8", G thread 3/8" BSP, without valve	-	759	In stock	Enquiry
SN-PHN8-8RP	H plug 1/2", G 1/2" BSP, without valve	-	759	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

SNAP-TITE quick coupling plug with internal BSP thread, American-made, without valve. Application: hydraulic power (hydraulic oil), industrial (water, steam, fuels and oils, gases, chemicals). Depending on the application, the appropriate material for the coupling and sealing must be selected. Standard: MIL-C-51234. Working pressure: up to 759 bar (depending on the size of the quick coupling), safety factor 2:1. Material: carbon steel, galvanized. Sealing: NBR. Operating temperature: from -35°C to +120°C. Flow has been provided for a pressure drop of 3 bar.