Can the Flat foam nozzle, GW 1/4" BSP, plastic operate safely at 3.5â4 bar for optimal foaming and also be used for spraying and rinsing?

Yes. The Flat foam nozzle, GW 1/4" BSP, plastic is designed for low-pressure foaming and gives best results at 3.5â4 bar, so operating it safely in that range is appropriate for optimal foam generation. The description specifies its intended foaming pressure (2.5 bar, with best performance at 3.5â4 bar) and notes that it can also be used for spraying and rinsing cleaned surfaces. The 1/4" BSP plastic construction supports these multifunctional uses, provided you follow standard precautions: do not exceed recommended pressure, ensure secure 1/4" BSP connection, inspect for damage or wear, and use compatible cleaning agents.

Is the Flat foam nozzle, GW 1/4" BSP, plastic compatible with standard 1/4" BSP hoses and fittings?

Yes. The Flat foam nozzle, GW 1/4" BSP, plastic is compatible with standard 1/4" BSP hoses and fittings. Its connection is specified as 1/4" BSP, so it will thread directly to any matching 1/4" BSP female or male threaded hose/fitting. Note that optimal foaming performance is at low pressure (2.5 bar, best 3.5â4 bar), and because the body is plastic, avoid excessive torque or incompatible chemicals that could damage the material.

Does the Flat foam nozzle, GW 1/4" BSP, plastic require special maintenance to prevent clogging when used with detergents?

Yes. some basic maintenance is recommended to prevent clogging when using the Flat foam nozzle, GW 1/4" BSP, plastic with detergents. Why: Detergents, especially those containing thickening agents, surfactants, or particulate additives, can leave residues that build up inside the plastic body and orifices over time. Small passages in foam nozzles are particularly prone to blockage, which reduces foam quality and spray performance. Recommended maintenance (simple, effective): - Rinse after each use: Immediately flush the nozzle with clean water (preferably warm) until water runs clear to remove detergent traces. - Periodic deep clean: Soak the nozzle in warm water with a mild detergent or a vinegar solution for 10â30 minutes, then rinse and blow out passages with compressed air if available. - Inspect and disassemble if possible: Check the nozzle opening and any removable parts for deposits; remove and clean components per manufacturer guidance. - Avoid aggressive chemicals: Strong solvents or abrasive cleaners can degrade plasticâuse manufacturer-approved cleaning solutions. - Filter and dilute: Use a fine filter on the supply line and follow recommended detergent dilution to reduce solids and viscosity that cause clogging. - Store dry: After cleaning, allow the nozzle to dry completely before storage to prevent microbial growth or residue hardening. Following these simple steps will keep the Flat foam nozzle, GW 1/4" BSP, plastic functioning reliably and prolong its service life.

Flat foam nozzle, GW 1/4″ BSP, plastic

Additional information

Flat nozzle made of plastic intended for foaming at low pressure – 2.5 bar (best results are achieved at 3.5 ÷ 4 bar). It can also be used for spraying and rinsing cleaned surfaces. Connection: 1/4″ BSP. Nozzle material: plastic.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
AK-LANF002	Flat foam nozzle, GW 1/4" BSP, nylon, black	-	4	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Flat nozzle made of plastic intended for foaming at low pressure – 2.5 bar (best results are achieved at 3.5 ÷ 4 bar). It can also be used for spraying and rinsing cleaned surfaces. Connection: 1/4″ BSP. Nozzle material: plastic.