What is the correct installation torque for Adaptor - T-piece "T", brass, type FR106 with internal UNF thread and 45Â° cone?

The correct installation torque for Adaptor - T-piece "T", brass, type FR106 (internal UNF thread, SAE type, 45Â° cone) depends on thread size and material (brass-to-brass). General recommended torque range for small brass UNF fittings with 45Â° cone is approximately 5â15 Nm for M6âM10 equivalent UNF sizes; for larger UNF sizes torque rises accordingly (e.g., up to ~20â40 Nm for sizes equivalent to 1/2" UNF). For precise, safe installation you must: - Verify the exact UNF thread size for FR106 (check product drawing or supplier datasheet). - Use the manufacturerâs specified torque if available. - If manufacturer data is unavailable, start at the lower end of the typical range for that thread size and tighten incrementally while checking for proper cone seating and leak tightness. - Apply appropriate thread lubricant or sealing compound only if specified; brass fittings with a 45Â° cone typically rely on metal-to-metal sealing, so avoid over-torquing which can deform the cone or thread. If you provide the exact UNF thread size (e.g., 1/8", 1/4", 3/8", 1/2" UNF), I will give a more specific torque value.

Can Adaptor - T-piece "T", brass, type FR106 be used with non-thermoplastic hoses or only FR 5 DN2 (1/12")?

Adaptor - T-piece "T", brass, type FR106 is described specifically as a fitting with sleeves for thermoplastic hose FR 5 DN2 (1/12"). That indicates it is designed and sized for that thermoplastic hose type and sleeve system. While the brass end and internal UNF thread/45Â° cone could physically connect to other hoses, safe and reliable use depends on matching outer diameter, sleeve compression, pressure rating and material compatibility. Therefore it should be used with FR 5 DN2 (1/12") thermoplastic hoses as specified; using it with non-thermoplastic hoses is not recommended unless you verify dimensional fit, sleeve sealing method and pressure compatibility with the hose manufacturer or perform appropriate testing.

Is Adaptor - T-piece "T", brass, type FR106 compatible with high-pressure applications?

Adaptor - T-piece "T", brass, type FR106 is intended for use with thermoplastic hose FR 5 DN2 (1/12") featuring internal UNF thread, SAE type, 45Â° cone, with brass end and sleeves. Based on this description, it is designed for low- to medium-pressure hydraulic or fluid connections typical for thermoplastic hose assemblies rather than for high-pressure systems. Key points: - Connection type: internal UNF thread with SAE 45Â° cone suggests sealing by cone-to-cone contact, common in medium-pressure hydraulic fittings but not equivalent to high-pressure metal-to-metal or crimped high-pressure fittings. - Hose compatibility: FR 5 thermoplastic hose (small bore DN2 / 1/12") is usually used in lower to moderate pressure ranges; thermoplastic hoses generally have lower burst and working pressures than reinforced steel braided hoses. - Materials: brass body and sleeves are corrosion-resistant and suitable for many fluids but have lower strength than steel or stainless steel used for high-pressure fittings. Conclusion: Adaptor - T-piece "T", brass, type FR106 is not recommended for high-pressure applications. It is suitable for low- to medium-pressure use consistent with thermoplastic hose specifications. For high-pressure systems, choose fittings and hoses rated explicitly for the required pressure, typically made of steel or stainless steel with appropriate pressure ratings and certifications.

Adapter – Tee “T”, brass, type FR106

Additional information

Material	B – brass (bronze)

Adapter – Tee “T” with ferrules for hose thermoplastic FR 5 DN2 (1/12″), with a female UNF thread, type SAE, 45° cone. Material fittings: brass. Material sleeve: brass.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
ZC-FR106-015	Tee type "T" for hose 1/12", 1/4" female SAE, 45° cone, brass	2	-	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Adapter – Tee “T” with ferrules for hose thermoplastic FR 5 DN2 (1/12″), with a female UNF thread, type SAE, 45° cone. Material fittings: brass. Material sleeve: brass.