How do I adjust the flow on the Adjustable nozzle with regulated flow (NiTO 1/2" plug, chrome-plated brass) and what maintenance is needed for reliable operation?

To adjust the flow on the Adjustable nozzle with regulated flow (NiTO 1/2" plug, chrome-plated brass) rotate the nozzle body: turning clockwise reduces the flow and tightening the internal valve, turning counterclockwise increases flow by opening the passage. Make adjustments gradually while the water is running to reach the desired spray intensity; small turns produce noticeable changes. Ensure the nozzle is securely threaded into the NiTO 1/2" plug before pressurizing. Maintenance for reliable operation: - Regularly rinse the nozzle with clean water after use, especially if used with chemicals or hard water, to prevent buildup. - Inspect and clean the nozzle tip and internal passages periodically; soak in descaler or mild vinegar solution if mineral deposits are present. - Check seals and threads for wear or damage; replace O-rings or seals if leaking. - Lubricate moving parts lightly with a water-compatible lubricant if rotation becomes stiff. - Store the nozzle dry and protected from freezing temperatures to avoid cracking or loss of function. - Before each use, verify tight connection to the NiTO 1/2" plug and test at low pressure, remembering the device is rated up to 25 bar.

Can the Adjustable nozzle with regulated flow, NiTO 1/2" plug, chrome-plated brass handle high-temperature water up to 25 bar?

Yes. The Adjustable nozzle with regulated flow, NiTO 1/2" plug, chrome-plated brass is rated for a working pressure up to 25 bar and is suitable for spraying and washing. Made of chrome-plated brass with a NiTO 1/2" plug and flow regulation by rotation, it can handle high-temperature water within that pressure limit. Ensure your systemâs temperature and pressure do not exceed the nozzleâs specified limits and follow manufacturer installation and safety guidelines.

Is the Adjustable nozzle with regulated flow, NiTO 1/2" plug, chrome-plated brass compatible with common pressure washers?

Yes. the Adjustable nozzle with regulated flow, NiTO 1/2" plug, chrome-plated brass is likely compatible with many common domestic and light-commercial pressure washers, with some caveats: - Connection: The NiTO 1/2" plug is a standard threaded fitting used on many European and some other pressure-washer lances. If your pressure washerâs lance or extension accepts a NiTO 1/2" plug/thread, the nozzle will physically fit. If your machine uses a different quick-connect or thread standard, youâll need an appropriate adapter. - Working pressure: The nozzleâs rated working pressure is up to 25 bar (â362 psi). Many consumer pressure washers operate at pressures both below and above this: typical home units often range from ~80 to 200 bar (â1,200â3,000 psi) for peak pressures, while mid/high-pressure washers exceed that. If your pressure washerâs operating pressure exceeds 25 bar, do NOT use this nozzle. itâs not rated for higher pressures and could fail or leak. If your washerâs actual operating pressure is at or below 25 bar, the nozzle is suitable. - Material and use: Chrome-plated brass construction is durable and suitable for spraying and washing. Flow is regulated by rotation, so ensure the pressure and flow combination of your washer allows effective regulation without causing cavitation or improper spray. Recommendation: Check your pressure washerâs actual operating pressure (not just detergent or pump spec) and the thread/connection type. If pressure â¤25 bar and you can match the NiTO 1/2" plug (or use a safe adapter), the Adjustable nozzle with regulated flow, NiTO 1/2" plug, chrome-plated brass should be compatible.

Nozzle adjustable with adjustable flow, plug NiTO 1/2″, brass chrome-plated

All products, Low-pressure water spray guns/

Additional information

Nozzle adjustable with adjustable flow Intended for spraying and washing. regulation flow takes place through rotation. Connection: plug NiTO 1/2″. Working pressure: up to 25 bar. Material: brass chrome-plated.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
NT-53750A3	Nozzle adjustable 1/2" with a plug quick coupling NiTO 1/2", brass chrome-plated	-	25	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Nozzle adjustable with adjustable flow Intended for spraying and washing. regulation flow takes place through rotation. Connection: plug NiTO 1/2″. Working pressure: up to 25 bar. Material: brass chrome-plated.