Is ANFOR 90Â° connector - hose end, galvanized steel, type A.26M suitable for continuous operation at working pressures up to 19 bar?

Yes. ANFOR 90Â° connector - hose end, galvanized steel, type A.26M is suitable for continuous operation at working pressures up to 19 bar, provided you select the correct connector size rated for that pressure. The product specification lists a working pressure range from 5 bar to 19 bar depending on connector size, so confirm the specific size/version of the A.26M you have or intend to buy is the one rated at 19 bar. Also ensure operating temperature remains within the specified -20Â°C to +50Â°C and install per manufacturer recommendations.

Can ANFOR 90Â° connector - hose end, galvanized steel, type A.26M be used for groundwater drainage and wastewater applications?

Yes. ANFOR 90Â° connector - hose end, galvanized steel, type A.26M is suitable for groundwater drainage and wastewater applications. The product description explicitly lists groundwater drainage, wastewater treatment plants and sewage discharge among intended uses. Its galvanized steel construction provides corrosion resistance, working pressures from 5 to 19 bar (size-dependent) cover typical pumping and drainage requirements, and an operating temperature range of -20Â°C to +50Â°C suits standard environmental conditions. Ensure you select the correct size for required pressure and flow, and confirm compatibility with your hose material and local regulations.

Does ANFOR 90Â° connector - hose end, galvanized steel, type A.26M require special maintenance for use in corrosive environments?

ANFOR 90Â° connector - hose end, galvanized steel, type A.26M does not inherently require special maintenance beyond standard care for galvanized steel when used in corrosive environments, but prudent precautions will extend service life and reliability. Recommended maintenance and precautions: - Regular inspections: check for visible corrosion, pitting, coating damage, leaks and mechanical wear. at intervals appropriate to the corrosivity of the environment (e.g., monthly in highly aggressive conditions, quarterly in moderate conditions). - Cleaning: remove salt deposits, chemical residues, mud and organic matter promptly using fresh water and a mild detergent; rinse thoroughly and dry where possible. - Touch-up protection: repair any damaged zinc coating or scratches with appropriate zinc-rich touch-up paint or cold galvanizing compound to limit localized corrosion. - Fastener and seal checks: ensure clamps, hose fittings and sealing surfaces remain tight and free from corrosion; replace worn gaskets or Oârings with chemically compatible materials. - Avoid dissimilar metals: minimize contact with copper, brass or stainless steels that can create galvanic corrosion unless insulated or isolated. - Environmental controls: where feasible reduce direct exposure to aggressive agents (acidic/alkaline chemicals, chloride salts, continuous splashing) or consider additional protective measures (local shielding, sacrificial anodes, or supplementary coatings). - Pressure and temperature monitoring: operate within the specified working pressure (5â19 bar depending on size) and temperature range (â20Â°C to +50Â°C); deviations can accelerate deterioration. - Replacement planning: in very aggressive service (continuous chemical exposure, seawater spray, sewage with strong oxidizers) plan shorter inspection intervals and earlier replacement or consider alternative materials (stainless steel or specially coated fittings). Following these practices will minimize corrosion risk and help maintain safe operation of the ANFOR 90Â° connector - hose end, galvanized steel, type A.26M in corrosive environments.

Connector ANFOR 90° plug – fitting for hose, steel galvanized, type A.26M

All products, Lever couplings/

Additional information

Material	CS – steel (cast iron)

Connector ANFOR plug with “tail” for hose for use among others in agriculture, horticulture, industry, construction, road and tunnel building, groundwater drainage, sewage treatment plants, wastewater discharge, and environmental protection. Material: steel galvanized. Working pressure: from 5 bar to 19 bar (depending on the coupling size). Operating temperature: from -20°C to +50°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
OM-A26M-90-150	Connector ANFOR 90° plug - Fitting for 150 mm hose, galvanized steel	150	12	In stock	Enquiry
OM-A26M-90-200	Connector ANFOR 90° plug - Fitting for 200 mm hose, galvanized steel	200	6	In stock	Enquiry
OM-A26M-90-250	Connector ANFOR 90° plug - Fitting for 250 mm hose, galvanized steel	250	5	In stock	Enquiry
OM-A26M-90-300	Connector ANFOR 90° plug - Fitting for 300 mm hose, galvanized steel	300	5	In stock	Enquiry
OM-A26M-90-400	Connector ANFOR 90° plug - Fitting for 400 mm hose, galvanized steel	400	5	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Connector ANFOR plug with “tail” for hose for use among others in agriculture, horticulture, industry, construction, road and tunnel building, groundwater drainage, sewage treatment plants, wastewater discharge, and environmental protection. Material: steel galvanized. Working pressure: from 5 bar to 19 bar (depending on the coupling size). Operating temperature: from -20°C to +50°C.