What is the maximum working pressure for the CAMLOCK DP socket cap, aluminum, made to MIL-C-27487 (A-A-59326) standards?

The maximum working pressure for the CAMLOCK DP socket cap, aluminum, made to MIL-C-27487 (A-A-59326) standards is up to 10 bar, depending on coupling size.

Does CAMLOCK DP socket cap, aluminum, meet MIL-C-27487 (A-A-59326) corrosion resistance requirements?

No - CAMLOCK DP socket cap, aluminum made of plain aluminum does not by itself meet MIL-C-27487 (A-A-59326) corrosion resistance requirements. The MILâCâ27487 (AâAâ59326) standard specifies material, treatments, and corrosion protection (e.g., specific aluminum alloys, coatings, anodizing or passivation) to achieve required corrosion resistance. A description stating only "End cap for CAMLOCK DP coupling made according to American military standard MILâCâ27487 (AâAâ59326). Working pressure: up to 10 bar, depending on coupling size. Material: aluminum." does not confirm the required corrosion treatments or alloy; therefore compliance cannot be assumed without documentation showing the specified alloy and corrosion protection processes were used.

How should I size the CAMLOCK DP socket cap, aluminum, made to MIL-C-27487 (A-A-59326) for different hose diameters?

To size the CAMLOCK DP socket cap, aluminum, made to MIL-C-27487 (A-A-59326) for different hose diameters, follow these guidelines: 1. Match nominal hose ID to CAMLOCK size: choose the CAMLOCK DP socket cap, aluminum whose nominal size equals the hose's internal diameter (ID) expressed in inches. Common pairings: - 1/2" hose â 1/2" CAMLOCK - 3/4" hose â 3/4" CAMLOCK - 1" hose â 1" CAMLOCK - 1-1/4" hose â 1-1/4" CAMLOCK - 1-1/2" hose â 1-1/2" CAMLOCK - 2" hose â 2" CAMLOCK - 2-1/2", 3", 4" hoses â corresponding CAMLOCK sizes 2. Verify hose OD and coupling spigot: if hose is defined by OD or uses a specific barbed/ferrule adapter, ensure the spigot or adapter matches the CAMLOCK DP socket cap bore and assembly method. For hoses with thicker walls (smaller ID vs OD), confirm the internal bore of the coupling accepts the mating spigot or adapter. 3. Check working pressure and safety margin: CAMLOCK DP socket cap, aluminum is rated up to 10 bar depending on size. Ensure the system working pressure is below the capâs rating for the selected size and allow margin for pressure spikes and temperature effects. 4. Consider material compatibility and application: aluminum suits many liquids but avoid in aggressive chemicals incompatible with aluminum or where galvanic corrosion is a concern. For abrasive or high-wear services, consider reinforced hose ends or alternative materials. 5. Confirm MIL-C-27487 (A-A-59326) dimensions: use manufacturer datasheets confirming dimensional tolerances for the CAMLOCK DP socket cap, aluminum to ensure proper fit with MIL-spec mating parts and any hose adapters. 6. Use proper hose termination: for secure connection, select correct ferrule/clamp or barbed insert sized to the hose OD and compatible with the CAMLOCK spigot. Crimped ferrules must match hose and coupling size per supplier recommendations. 7. Test assembly: after installation, perform pressure/leak test at working pressure (plus safety margin) and inspect for slippage. Summary: Select the CAMLOCK DP socket cap, aluminum by matching the nominal CAMLOCK size to the hose internal diameter (or to the mating adapter/ferrule size), confirm bore and spigot compatibility, verify pressure rating (â¤10 bar as applicable), and use proper termination and testing to ensure secure fit.

CAMLOCK DP socket cap, aluminum

Additional information

Material	AL – aluminum

End cap for CAMLOCK DP coupling made according to American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 10 bar, depending on coupling size. Material: aluminum.

List of product variants

Article number	Product variant name	Nominal inner diameter	Working pressure [bar]
AC-DP-050-A	CAMLOCK connector DP 1/2" aluminum	-	9
AC-DP-050-AX	CAMLOCK connector DP 1/2", aluminum	-	9
AC-DP-075-A	CAMLOCK connector DP 3/4" aluminum	-	10
AC-DP-075-AX	CAMLOCK connector DP 3/4" aluminum	-	10
AC-DP-100-A	CAMLOCK DP 1" aluminum connector	-	10
AC-DP-100-AX	CAMLOCK DP 1" aluminum connector	-	10
AC-DP-125-A	CAMLOCK connector DP 1.1/4" aluminum	-	10
AC-DP-125-AX	CAMLOCK connector DP 1.1/4" aluminum	-	10
AC-DP-150-A	CAMLOCK connector DP 1.1/2" aluminum	-	10
AC-DP-150-AX	CAMLOCK connector DP 1.1/2", aluminum	-	10
AC-DP-200-A	CAMLOCK DP 2" aluminum connector	-	10
AC-DP-200-AX	CAMLOCK DP 2" aluminum connector	-	10
AC-DP-250-A	CAMLOCK DP 2.1/2" aluminum connector	-	10
AC-DP-250-AX	CAMLOCK connector DP 2.1/2" aluminum	-	10
AC-DP-300-A	CAMLOCK DP 3" aluminum connector	-	10
AC-DP-300-AX	CAMLOCK DP 3" aluminum connector	-	10
AC-DP-400-A	CAMLOCK DP 4" aluminum connector	-	10
AC-DP-400-AX	CAMLOCK DP 4" aluminum connector	-	10
AC-DP-500-A	CAMLOCK DP 5" aluminum connector	-	5
AC-DP-500-AX	CAMLOCK DP 5" connector, aluminum	-	5
AC-DP-600-A	CAMLOCK connector DP 6" aluminum	-	5
AC-DP-600-AX	CAMLOCK connector DP 6", aluminum	-	5

End cap for CAMLOCK DP coupling made according to American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 10 bar, depending on coupling size. Material: aluminum.