Is the CEJN 116 quick-connect socket with GW at 90Â° angle with valve, hardened steel compatible with my hydraulic press rated at 1500 bar?

Yes . the CEJN 116 quick-connect socket with GW at 90Â° angle with valve, hardened steel is compatible with your hydraulic press rated at 1500 bar, provided the system uses compatible thread and coupling types. Key points from the product spec: - Working pressure (connected coupling): 1500 bar . matches your press rating. - Burst pressure: 3000 bar . provides safety margin. - Designed specifically for very high-pressure hydraulic installations and listed uses include hydraulic presses. - Material and sealing: hardened, galvanized steel with NBR seals . suitable for typical hydraulic fluids and high-pressure use within the stated temperature range (-30 Â°C to +100 Â°C). - Flow and size: nominal diameter 2.5 mm, flow 6 l/min (Îp = 4 bar) . ensure this flow and diameter meet your application requirements. - Optional safety ring and protective cap enhance safety and contamination protection. Final check: confirm thread compatibility (GW/internal thread type and size) and compatibility of NBR seals with your hydraulic fluid. If both match, the CEJN 116 socket is suitable for use on a 1500 bar hydraulic press.

Can the CEJN 116 quick-connect socket with GW at 90Â° angle with valve, hardened steel be fitted with a safety ring for high-pressure rescue tools?

Yes. The CEJN 116 quick-connect socket with GW at 90Â° angle with valve, hardened steel can be fitted with a safety ring for high-pressure rescue tools - the socket can optionally be equipped with a safety ring to prevent accidental disconnection. It is designed for very high-pressure hydraulic applications (working pressure 1500 bar, burst 3000 bar), hardened galvanized steel construction, and is suitable for rescue equipment and other high-pressure tools.

Can the CEJN 116 quick-connect socket with GW at 90Â° angle with valve, hardened steel be used with NBR seals in low-temperature environments down to -30Â°C?

Yes. The CEJN 116 quick-connect socket with GW at 90Â° angle with valve, hardened steel can be used with NBR seals in environments down to â30Â°C. The product specification lists the sealing material as NBR and the operating temperature range as â30Â°C to +100Â°C, so NBR is acceptable at that lower limit. Notes and practical considerations: - NBR (nitrile) retains adequate sealing properties at â30Â°C but becomes stiffer and less flexible as temperature decreases; this can slightly increase leak risk during dynamic movement or repeated coupling/uncoupling. - For static, low-movement applications at â30Â°C the performance should be reliable. For frequent coupling cycles, shock/impact, or critical zero-leak requirements, test the assembly under actual field conditions. - Ensure proper lubrication/handling at low temperatures and consider protective measures (e.g., warming before operation) if you observe increased stiffness or difficulty in mating/separating couplings. - If extended use below â30Â°C or markedly improved low-temperature flexibility is required, consider alternative seal materials rated for lower temperatures (e.g., FKM, silicone, or polyurethane) after checking compatibility with hydraulic fluid and pressure.

CEJN 116 quick-coupling socket with female thread at a 90° angle with a valve, hardened steel

All products, UHP quick couplings/

Additional information

Material	CS – steel (cast iron)

CEJN 116 quick-coupling socket with a female thread, for connection at a 90° angle and with a valve intended for hydraulic installations at very high pressures. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. An ideal solution in small spaces. Optionally, the socket can be fitted with a ring to prevent accidental disconnection. Supplied as standard with a cap to protect against contamination. Material: hardened steel, galvanized. Sealing: NBR. Flow: 6 l/min (Δp = 4 bar). Nominal diameter: 2.5 mm. Working pressure: 1500 bar (coupling connected). Burst pressure: 3000 bar. Operating temperature: from -30°C to +100°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
CJ-HP-101161230	Socket CEJN 116 1/4" BSP female with an angled 90° connection	-	1500	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

CEJN 116 quick-coupling socket with a female thread, for connection at a 90° angle and with a valve intended for hydraulic installations at very high pressures. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. An ideal solution in small spaces. Optionally, the socket can be fitted with a ring to prevent accidental disconnection. Supplied as standard with a cap to protect against contamination. Material: hardened steel, galvanized. Sealing: NBR. Flow: 6 l/min (Δp = 4 bar). Nominal diameter: 2.5 mm. Working pressure: 1500 bar (coupling connected). Burst pressure: 3000 bar. Operating temperature: from -30°C to +100°C.