Can Clamp DIN 3015 standard, polypropylene, type 100 be welded to steel structures without degrading clamp performance at -30Â°C to +90Â°C?

Clamp DIN 3015 standard, polypropylene, type 100 can be welded to steel structures, but with important caveats to avoid degrading clamp performance at -30Â°C to +90Â°C. Key points: - The clamp base and base material are carbon steel and intended to be welded to the structure; welding the steel base (not the polypropylene body) is the normal mounting method per the product description. - Polypropylene body must not be exposed to welding heat or splatter. During welding, ensure the polypropylene clamp body and screws are protected or removed; local temperatures from welding can deform or char polypropylene, compromising mechanical grip and chemical/thermal performance. - Use proper welding procedures: weld only the steel base to the structure, control heat input, use tack-welds or intermittent welds if specified, and allow controlled cooling to avoid transmitting excessive heat into the plastic. - Post-weld inspection: verify clamp geometry, absence of heat damage, and secure attachment. Replace clamps showing any deformation, melting, or reduced screw engagement. - Corrosion protection: galvanized screws and carbon-steel base require suitable corrosion protection for marine/ground use; welding may alter coatings.reapply coatings or use suitable materials. - Temperature range: if installed correctly (steel base welded only, plastic protected), the assembled clamp is intended to operate from -30Â°C to +90Â°C as specified. Conclusion: Yes.Clamp DIN 3015 standard, polypropylene, type 100 may be welded to steel structures when the weld is confined to the steel base and welding practices protect the polypropylene components and fasteners. Ensure proper welding technique, protection, and post-weld inspection to maintain performance across -30Â°C to +90Â°C.

Can Clamp DIN 3015 standard, polypropylene, type 100 be used in marine environments without corroding the galvanized screws or carbon steel base?

Clamp DIN 3015 standard, polypropylene, type 100 can be used in marine environments but with reservations. Polypropylene body resists seawater and UV reasonably well; however, the supplied galvanized screws and carbon steel base are susceptible to corrosion in marine atmospheres (salt spray, high humidity). Galvanized screws may suffer accelerated coating breakdown and rust; the carbon steel base will corrode unless properly surfaceâtreated (hotâdip galvanizing, marine grade coating) or replaced with stainless steel. For durable marine service, specify corrosionâresistant fasteners and base (A4/316 stainless or properly treated steel) or order extended plates/rails and screws in marine grades and confirm selection with TUBES INTERNATIONALÂ®. Operating temperature is acceptable.

Is Clamp DIN 3015 standard, polypropylene, type 100 suitable for UV-exposed outdoor installations without degradation?

Clamp DIN 3015 standard, polypropylene, type 100 Format: No. polypropylene clamps of this description are generally not suitable for prolonged UV-exposed outdoor installations without degradation. Standard polypropylene (especially colored/green grade used here) will degrade under sunlight over time: UV causes surface chalking, embrittlement, loss of mechanical strength and eventual cracking, especially under cyclic loads, temperature swings and contact stress from clamped pipes. The listed operating temperature range (â30 Â°C to +90 Â°C) does not imply UV resistance. Mitigation options: - Use UV-stabilized or UV-resistant polypropylene grade (confirm with supplier). - Apply UV-protective coatings or paints rated for polypropylene. - Choose a UV-resistant material alternative (e.g., stainless steel, UV-stabilized PA, or specially formulated PVC/PC blends). - Provide shading or install in locations protected from direct sunlight. Recommendation: Consult TUBES INTERNATIONALÂ® to confirm whether the supplied green polypropylene is UV-stabilized; if not, specify a UV-resistant material or alternative mounting solution for long-term outdoor exposure.

Clamp DIN 3015 standard, polypropylene, type 100

All products, Clamps for hydraulic pipes/

Additional information

Material	P – material (plastic)

DIN 3015 standard clamp type 100 (without top plate) designed for quick, easy, durable, and aesthetic mounting of pipes, hoses, and hoses in various industrial sectors, in ground and marine installations. Manufactured according to DIN 3015 standard. The clamp is mounted to the structure using welding of the clamp base (there is an option for bolting or mounting on a rail). The clamp typically features a profiled (grooved) surface for the pipe opening. For size group 0, there is one hexagon socket screw, and for size groups 1 to 6, there are two hexagon socket screws. In addition to standard metal components, extended plates, rails, and screws for mounting clamp sets can be ordered. Selection of components should be consulted with TUBES INTERNATIONAL®. Clamp material: green polypropylene. Screw material: galvanized steel. Base material: carbon steel. Operating temperature: from -30°C to +90°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TC-PP100-006	DIN3015 standard PP clamp for 6 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-008	DIN3015 standard PP clamp for 8 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-010	DIN3015 standard PP clamp for 10 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-012	DIN3015 standard PP clamp for 12 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-106	DIN3015 standard PP clamp for 6 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-106,4	DIN3015 standard PP clamp for 6.4 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PP100-108	DIN3015 standard PP clamp for 8 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-109,5	DIN3015 standard PP clamp for 9.5 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-110	DIN3015 standard PP clamp for 10 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-112	DIN3015 standard PP clamp for 12 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PP100-212,7	DIN3015 standard PP clamp for 12.7 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-213,5	DIN3015 standard PP clamp for 13.5 mm pipe, without mounting accessories.	-	-	In stock	Enquiry
TC-PP100-214	DIN3015 standard PP clamp for 14 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PP100-215	DIN3015 standard PP clamp for 15 mm pipe, without mounting accessories.	-	-	In stock	Enquiry
TC-PP100-216	DIN3015 standard PP clamp for 16 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-217,2	DIN3015 standard PP clamp for 17.2 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PP100-218	DIN3015 standard PP clamp for 18 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-219	DIN3015 standard PP clamp for 19 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-319	DIN3015 standard PP clamp for 19 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-320	DIN3015 standard PP clamp for 20 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-321,3	DIN3015 standard PP clamp for 21.3 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-322	DIN3015 standard PP clamp for 22 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-325	DIN3015 standard PP clamp for 25 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-325,4	DIN3015 standard PP clamp for 25.4 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PP100-426,9	DIN3015 standard PP clamp for 26.9 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PP100-428	DIN3015 standard PP clamp for 28 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-430	DIN3015 standard PP clamp for 30 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-432	DIN3015 standard PP clamp for 32 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PP100-532	DIN3015 standard PP clamp for 32 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-533,7	DIN3015 standard PP clamp for 33.7 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PP100-535	DIN3015 standard PP clamp for 35 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PP100-538	DIN3015 standard PP clamp for 38 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-540	DIN3015 standard PP clamp for 40 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PP100-542	DIN3015 standard PP clamp for 42 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PP100-542,4	DIN3015 standard PP clamp for 42.4 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PP100-545	DIN3015 standard PP clamp for 45 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PP100-644,5	DIN3015 standard PP clamp for 44.5 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PP100-648,3	DIN3015 standard PP clamp for 48.3 mm pipe, without mounting accessories.	-	-	In stock	Enquiry
TC-PP100-650,8	DIN3015 standard PP clamp for 50.8 mm pipe, without mounting accessories.	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

DIN 3015 standard clamp type 100 (without top plate) designed for quick, easy, durable, and aesthetic mounting of pipes, hoses, and hoses in various industrial sectors, in ground and marine installations. Manufactured according to DIN 3015 standard. The clamp is mounted to the structure using welding of the clamp base (there is an option for bolting or mounting on a rail). The clamp typically features a profiled (grooved) surface for the pipe opening. For size group 0, there is one hexagon socket screw, and for size groups 1 to 6, there are two hexagon socket screws. In addition to standard metal components, extended plates, rails, and screws for mounting clamp sets can be ordered. Selection of components should be consulted with TUBES INTERNATIONAL®. Clamp material: green polypropylene. Screw material: galvanized steel. Base material: carbon steel. Operating temperature: from -30°C to +90°C.