Is the DIN 3015 standard insert, polyamide, type 101 suitable for continuous use at +180Â°C?

Yes. The DIN 3015 standard insert, polyamide, type 101 is specified with an operating temperature range from â40Â°C to +180Â°C, and the insert material is selfâextinguishing polyamide. Based on that specification, it is suitable for continuous use at +180Â°C within the stated operating limits. Ensure application-specific factors (mechanical load, chemical exposure, longâterm creep, UV/radiation, and any local temperature spikes above +180Â°C) are evaluated, since exceeding the specified range or exposing the polyamide to degrading agents can reduce performance and safety.

Can DIN 3015 standard insert, polyamide, type 101 withstand low-temperature use down to -40Â°C without becoming brittle?

Yes. DIN 3015 standard insert, polyamide, type 101 is specified with an operating temperature range from â40Â°C to +180Â°C. That means it is designed to function down to â40Â°C and, per the manufacturerâs specification, should not become brittle within that range. Always verify with the supplier for specific batch material properties, any additives or UV/chemical exposures, and perform application-specific testing if the clamp will face impact loads or prolonged low-temperature cycling.

Does DIN 3015 standard insert, polyamide, type 101 resist chemical exposure from common hydraulic fluids?

Generally yes, but with limitations. DIN 3015 standard insert, polyamide, type 101 is made of self-extinguishing polyamide and is suitable for use in hydraulic clamping environments against many common hydraulic fluids (mineral oilâbased fluids, most petroleum hydraulic oils). Polyamide has good chemical resistance to oils, greases and many hydraulic fluids at normal temperatures, and the insertâs operating range (â40 Â°C to +180 Â°C) covers typical hydraulic system temperatures. Limitations and cautions: - Polyamide resistance varies by formulation and can be compromised by prolonged exposure to certain aggressive fluids (some fireâresistant fluids, phosphate esters, strong acids/alkalis, esterâbased fluids, and some solvents). These can cause swelling, softening or loss of mechanical properties. - Higher temperatures near the upper limit (+180 Â°C) accelerate chemical attack and degrade longâterm resistance. - Additives in hydraulic fluids (water content, detergents, glycol, etc.) can affect compatibility. - Dynamic or highâpressure fluid contact, leaks, or immersion expose the part more than incidental contact and increase risk. Recommendation: Verify compatibility with the specific hydraulic fluid and operating conditions. Consult the polyamide material data sheet from the manufacturer or run compatibility tests with the exact fluid (and temperature) planned for use. If compatibility is uncertain or fluids are aggressive (phosphate ester, glycol, esters, solvents), consider alternative materials or protective measures.

Insert DIN 3015 standard, polyamide, type 101

All products, Clamps for hydraulic pipes/

Additional information

Material	P – material (plastic)

A two-part insert of a DIN 3015 type 101 clamp, made in accordance with the DIN 3015 standard. For dimension group 0 there is one bolt hole, for dimension groups 1 ÷ 6 there are two bolt holes. As standard, it has a profiled (grooved) surface of the pipe hole. Material insert: self-extinguishing polyamide. Operating temperature: from -40°C to +180°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TC-PA101-006X	Insert DIN3015 standard PA for a 6 mm pipe	-	-	In stock	Enquiry
TC-PA101-008X	Insert DIN3015 standard PA for a 8 mm pipe	-	-	In stock	Enquiry
TC-PA101-010X	Insert DIN3015 standard PA for a 10 mm pipe	-	-	In stock	Enquiry
TC-PA101-012X	Insert DIN3015 standard PA for a 12 mm pipe	-	-	In stock	Enquiry
TC-PA101-106,4X	Insert DIN3015 standard PA for a 6.4 mm pipe	-	-	In stock	Enquiry
TC-PA101-106X	Insert DIN3015 standard PA for a 6 mm pipe	-	-	In stock	Enquiry
TC-PA101-108X	Insert DIN3015 standard PA for a 8 mm pipe	-	-	In stock	Enquiry
TC-PA101-109,5X	Insert DIN3015 standard PA for a 9.5 mm pipe	-	-	In stock	Enquiry
TC-PA101-110X	Insert DIN3015 standard PA for a 10 mm pipe	-	-	In stock	Enquiry
TC-PA101-112X	Insert DIN3015 standard PA for a 12 mm pipe	-	-	In stock	Enquiry
TC-PA101-212,7X	Insert DIN3015 standard PA for a 12.7 mm pipe	-	-	In stock	Enquiry
TC-PA101-213,5X	Insert DIN3015 standard PA for a 13.5 mm pipe	-	-	In stock	Enquiry
TC-PA101-214X	Insert DIN3015 standard PA for a 14 mm pipe	-	-	In stock	Enquiry
TC-PA101-215X	Insert DIN3015 standard PA for a 15 mm pipe	-	-	In stock	Enquiry
TC-PA101-216X	Insert DIN3015 standard PA for a 16 mm pipe	-	-	In stock	Enquiry
TC-PA101-217,2X	Insert DIN3015 standard PA for a 17.2 mm pipe	-	-	In stock	Enquiry
TC-PA101-218X	Insert DIN3015 standard PA for a 18 mm pipe	-	-	In stock	Enquiry
TC-PA101-219X	Insert DIN3015 standard PA for a 19 mm pipe	-	-	In stock	Enquiry
TC-PA101-319X	Insert DIN3015 standard PA for a 19 mm pipe	-	-	In stock	Enquiry
TC-PA101-320X	Insert DIN3015 standard PA for a 20 mm pipe	-	-	In stock	Enquiry
TC-PA101-321,3X	Insert DIN3015 standard PA for a 21.3 mm pipe	-	-	In stock	Enquiry
TC-PA101-322X	Insert DIN3015 standard PA for a 22 mm pipe	-	-	In stock	Enquiry
TC-PA101-325,4X	Insert DIN3015 standard PA for a 25.4 mm pipe	-	-	In stock	Enquiry
TC-PA101-325X	Insert DIN3015 standard PA for a 25 mm pipe	-	-	In stock	Enquiry
TC-PA101-426,9X	Insert DIN3015 standard PA for a 26.9 mm pipe	-	-	In stock	Enquiry
TC-PA101-428X	Insert DIN3015 standard PA for a 28 mm pipe	-	-	In stock	Enquiry
TC-PA101-430X	Insert DIN3015 standard PA for a 30 mm pipe	-	-	In stock	Enquiry
TC-PA101-432X	Insert DIN3015 standard PA for a 32 mm pipe	-	-	In stock	Enquiry
TC-PA101-532X	Insert DIN3015 standard PA for a 32 mm pipe	-	-	In stock	Enquiry
TC-PA101-533,7X	Insert DIN3015 standard PA for a 33.7 mm pipe	-	-	In stock	Enquiry
TC-PA101-535X	Insert DIN3015 standard PA for a 35 mm pipe	-	-	In stock	Enquiry
TC-PA101-538X	Insert DIN3015 standard PA for a 38 mm pipe	-	-	In stock	Enquiry
TC-PA101-540X	Insert DIN3015 standard PA for a 40 mm pipe	-	-	In stock	Enquiry
TC-PA101-542,4X	Insert DIN3015 standard PA for a 42.4 mm pipe	-	-	In stock	Enquiry
TC-PA101-542X	Insert DIN3015 standard PA for a 42 mm pipe	-	-	In stock	Enquiry
TC-PA101-545X	Insert DIN3015 standard PA for a 45 mm pipe	-	-	In stock	Enquiry
TC-PA101-644,5X	Insert DIN3015 standard PA for a 44.5 mm pipe	-	-	In stock	Enquiry
TC-PA101-648,3X	Insert DIN3015 standard PA for a 48.3 mm pipe	-	-	In stock	Enquiry
TC-PA101-650,8X	Insert DIN3015 standard PA for a 50.8 mm pipe	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

A two-part insert of a DIN 3015 type 101 clamp, made in accordance with the DIN 3015 standard. For dimension group 0 there is one bolt hole, for dimension groups 1 ÷ 6 there are two bolt holes. As standard, it has a profiled (grooved) surface of the pipe hole. Material insert: self-extinguishing polyamide. Operating temperature: from -40°C to +180°C.