Is the DN 6 quick-connect plug with tube, no thread, TST 060 series, brass suitable for steam and hot oil applications at 25 bar?

Yes. The DN 6 quick-connect plug with tube, no thread, TST 060 series, brass is specified for use with hot oil and steam and has a working pressure rating of 25 bar, so it is suitable for steam and hot oil applications up to that pressure. Notes and precautions: - Ensure system temperature does not exceed the brass material and seal ratings (verify gasket/seal materials used with the coupling for high-temperature steam or hot oil). - Confirm compatibility of any connected components (hoses, clamps, mating couplings) with high temperature and 25 bar pressure. - Follow proper installation, regular inspection, and maintenance to avoid leaks or failure under thermal cycling.

Can the DN 6 quick-connect plug with tube, no thread, TST 060 series, brass be used for potable (drinking) water applications?

DN 6 quick-connect plug with tube, no thread, TST 060 series, brass - based on the description, it can be used for potable water only if the brass alloy and any internal seals meet drinking-water standards (e.g., NSF/ANSI 61, WRAS, or local potable-water approvals). The spec lists use for water in cleaning machines, hot oil and steam and shows 6 mm flow and 25 bar working pressure, but it does not state compliance with potable-water certification or lead content limits. Before using for drinking water, verify manufacturer certification for potable use and that materials (brass alloy and seals) comply with your jurisdictionâs potable-water regulations.

Does the DN 6 quick-connect plug with tube, no thread, TST 060 series, brass require special maintenance for steam use?

DN 6 quick-connect plug with tube, no thread, TST 060 series, brass can be used with steam (per product description). For safe, reliable steam service it does require some specific maintenance and checks: - Regular inspection: check sealing surfaces, Oârings and the locking ring for wear, hardening, cuts or deformation. Steam accelerates Oâring degradation compared with water. - Oâring material: ensure Oârings are made of steamâcompatible material (e.g., EPDM, PTFE or other highâtemperature elastomers). Replace with correct material if original is not steamârated. - Lubrication: use only highâtemperature, steamâcompatible lubricants on moving parts and Oârings to prevent sticking and extrusion. - Pressure/temperature limits: confirm operating steam pressure and temperature stay within the couplingâs rated limits (working pressure 25 bar and the brass temperature limits). Avoid thermal shocks; allow gradual heating/cooling. - Scale and condensate management: steam can cause scale or carry particulatesâperiodically flush and descale the coupling and connected tubing; drain condensate to prevent water hammer and corrosion. - Corrosion check: brass resists many conditions but inspect for dezincification or corrosion periodically, especially with wet steam or aggressive water chemistries. - Functional test: cycle the coupling under service conditions to verify sealing and locking function and to detect leaks. - Replacement interval: replace seals and worn components proactively based on inspection frequency and service severity. If uncertain about Oâring material or maximum allowable temperature for your specific installation, consult the manufacturerâs technical data or supplier to confirm steam rating and recommended seal materials before prolonged steam use.

DN 6 quick-connect plug with tube, no thread, TST 060 series, brass

Additional information

Material	B – brass (bronze)

DN 6 quick coupling plug with tube, without thread, for locking ring. Widely used in the industry for cooling injection molds and casting parts made of plastics, aluminum, brass, and zinc alloys. Can be used for water in cleaning machines, hot oil, and steam. Flow diameter: 6 mm. Working pressure: 25 bar. Material: brass.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
FW-060-BU063	DN 6 plug with 8 mm tube, L=63 mm, without valve	-	25	In stock	Enquiry
FW-060-BU100	DN 6 plug with 10 mm tube, L=100 mm, without valve	-	25	In stock	Enquiry
FW-060-BU120	DN 6 plug with 10 mm tube, L=120 mm, without valve	-	25	In stock	Enquiry
FW-060-BU240	DN 6 plug with 10 mm tube, L=240 mm, without valve	-	25	In stock	Enquiry
FW-060-BU360	DN 6 plug with 10 mm tube, L=360 mm, without valve	-	25	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

DN 6 quick coupling plug with tube, without thread, for locking ring. Widely used in the industry for cooling injection molds and casting parts made of plastics, aluminum, brass, and zinc alloys. Can be used for water in cleaning machines, hot oil, and steam. Flow diameter: 6 mm. Working pressure: 25 bar. Material: brass.