Can a CAMLOCK connector thread flat gasket, polyurethane withstand continuous use at temperatures between -20Â°C and +70Â°C without losing sealing performance?

Yes. A CAMLOCK connector thread flat gasket, polyurethane specified with an operating temperature range from -20Â°C to +70Â°C is suitable for continuous use within those limits without losing sealing performance, provided installation and service conditions match standard expectations. Polyurethane offers good mechanical strength, elasticity and abrasion resistance across this temperature band, maintaining the compressibility and recovery needed to keep a reliable seal on the internal thread to external cylindrical thread interface. Caveats: long-term performance depends on factors not stated (chemical exposure, pressure cycles, static vs. dynamic sealing, UV/ozone exposure, mechanical misalignment, and installation compression). If the application involves aggressive chemicals, continuous immersion, excessive pressures, frequent disconnects, or temperatures outside the stated range, verify compatibility with the supplier or perform testing.

Is the CAMLOCK connector thread flat gasket, polyurethane compatible with common chemicals used in industrial fluid transfer?

CAMLOCK connector thread flat gasket, polyurethane: Generally polyurethane offers good resistance to oils, hydrocarbons, hydraulic fluids, and many common industrial solvents, so it is compatible with a wide range of chemicals used in industrial fluid transfer. However, polyurethane has limited resistance to strong acids, strong bases, aromatic hydrocarbons (e.g., toluene, xylene) and certain chlorinated solvents, which can cause swelling, softening or degradation. Also temperature limits (-20Â°C to +70Â°C) must be observed, as chemical resistance worsens near extremes. For specific media (concentration, temperature, exposure time) verify compatibility with manufacturer chemical-resistance data or perform a compatibility test before service.

How should I store a CAMLOCK connector thread flat gasket, polyurethane to preserve its sealing properties?

To preserve the sealing properties of a CAMLOCK connector thread flat gasket, polyurethane, follow these storage best practices: - Clean and dry: Store gaskets clean and completely dry. Remove dust, dirt, oils or solvents before storage to prevent chemical degradation. - Temperature control: Keep within a stable range near room temperature. Avoid extremes outside the materialâs operating range (-20Â°C to +70Â°C). Prolonged exposure to temperatures near the limits can accelerate hardening or softening. - Avoid UV and ozone: Polyurethane degrades with UV light and ozone exposure. Store in opaque, UV-blocking packaging or inside boxes in a dark area. - Low humidity and ventilated: Moderate humidity is acceptable, but avoid very damp environments that encourage mold or promote hydrolysis. Ensure good air circulation. - Flat, strain-free positioning: Lay CAMLOCK connector thread flat gasket, polyurethane flat and unsupported by sharp edges or bends. Do not stack heavy loads on top to prevent deformation or permanent set. - Chemical isolation: Keep away from solvents, fuels, strong acids/alkalis, and plasticizers (e.g., oils, greases) which can swell or degrade polyurethane. Use sealed packaging if stored near such materials. - Clean packaging: Use clean, inert materials (polyethylene bags, cardboard boxes) for packaging. If long-term storage is expected, use vacuum-sealed or nitrogen-flushed packaging to minimize oxygen exposure. - Rotation and inspection: For long storage, rotate stock (first in, first out) and inspect periodically for signs of hardening, cracking, tackiness, discoloration or dimensional change. Replace any gasket showing deterioration. - Avoid compression set: If gaskets are stored in compressed form, use spacers to relieve constant compression. Prolonged compression can cause permanent set and loss of sealing ability. Following these guidelines will help maintain the elasticity, dimensions and sealing performance of your CAMLOCK connector thread flat gasket, polyurethane.

CAMLOCK connector thread flat gasket, polyurethane

Additional information

Maximum operating temperature [°C]	70
Minimum operating temperature [°C]	-20

Flat gasket for CAMLOCK AU and DU connections designed to seal the internal thread connection with the external cylindrical thread. Material: polyurethane. Operating temperature: from -20°C to +70°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AC-GU-075-P	PUR gasket for AU and DU 3/4"	-	-	In stock	Enquiry
AC-GU-100-P	PUR gasket for AU and DU 1"	-	-	In stock	Enquiry
AC-GU-125-P	PUR gasket for AU and DU 1.1/4"	-	-	In stock	Enquiry
AC-GU-150-P	PUR gasket for AU and DU 1.1/2"	-	-	In stock	Enquiry
AC-GU-200-P	PUR gasket for AU and DU 2"	-	-	In stock	Enquiry
AC-GU-250-P	PUR gasket for AU and DU 2.1/2"	-	-	In stock	Enquiry
AC-GU-300-P	PUR gasket for AU and DU 3"	-	-	In stock	Enquiry
AC-GU-400-P	PUR gasket for AU and DU 4"	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Flat gasket for CAMLOCK AU and DU connections designed to seal the internal thread connection with the external cylindrical thread. Material: polyurethane. Operating temperature: from -20°C to +70°C.