Is the GOST connector with female thread, bronze suitable for use with steam or gases?

No. The GOST connector with female thread, bronze is not suitable for use with steam or gases. The product description explicitly states it is intended for transmission and handling installations for liquid and bulk substances and is not suitable for steam and gases. Additionally, its sealing material (NBR rubber) and operating temperature range (â10Â°C to +80Â°C) limit its compatibility with steam and many gases, which often require higher temperatures and different seal materials. Working pressure is 10 bar, but that alone does not make it safe for steam or gas service given the stated exclusion.

Can the GOST connector with female thread, bronze be used in systems handling corrosive liquids or abrasive bulk materials?

Yes, the GOST connector with female thread, bronze can be used with some corrosive liquids and abrasive bulk materials, but with restrictions. Bronze offers good corrosion resistance to many water-based and mildly corrosive fluids, yet it can be attacked by strong acids, alkalis, chlorides or ammonia - so compatibility must be checked against the specific chemical. For abrasive bulk materials bronze is moderately wear-resistant but abrasion will shorten service life; pneumatic/suction conveying of abrasive powders/grit may require harder materials or sacrificial liners. Additional limits: max working pressure 10 bar, sealing is NBR (suitable for many oils, water and some chemicals but not for strong solvents/high temps), and operating temperature range is â10Â°C to +80Â°C. Not suitable for steam or gases. Conduct a compatibility and wear assessment for your specific media and conditions.

What maintenance is required for the GOST connector with female thread, bronze to ensure NBR seals remain effective?

For the GOST connector with female thread, bronze, to ensure NBR seals remain effective, follow these maintenance practices: - Regular inspection: check seals visually and by touch every 1â3 months in normal use (more often under heavy duty). Look for cracking, hardening, swelling, cuts, compression set, or extrusion of the NBR gasket. - Cleanliness: keep sealing surfaces, thread and mating parts free of dirt, debris and chemical residues. Clean with a soft cloth and mild detergent; avoid solvents that can degrade NBR (e.g., ketones, strong hydrocarbons). - Lubrication: apply a thin film of compatible lubricant (silicone-free, NBR-safe greases or light mineral oil approved for NBR) to the seal and threads to reduce friction and prevent drying. Do not over-lubricateâexcess oil can attract dirt. - Torque and assembly: tighten to manufacturerâs recommended torque or hand-tight plus specified fraction to avoid over-compression that causes permanent deformation or under-tightening that allows leaks. Use correct alignment to prevent twisting or pinching the seal. - Temperature and pressure respect: operate within specified limits (â10Â°C to +80Â°C, up to 10 bar). Avoid thermal or pressure shocks which accelerate NBR ageing and can cause seal failure. - Chemical compatibility: ensure transferred media are compatible with NBR. Do not use the connector for steam or gases. If media change, inspect or replace seals before reuse. - Replacement interval: replace NBR seals at first sign of deterioration or on a preventive schedule (typical service life variesâinspect yearly and consider replacement every 1â5 years depending on conditions). - Storage: store spare NBR seals in cool, dark, dry conditions away from ozone, direct sunlight, and sources of heat or hydrocarbons; keep in original packaging when possible. - Documentation: log inspections, maintenance actions, and replacements to detect trends and optimize intervals. Following these steps will maintain sealing integrity and prolong service life of the GOST connector with female thread, bronze.

GOST connector with female thread, bronze

All products, Symmetrical claw couplings/

Additional information

Material	B – brass (bronze)

GOST connector with internal thread intended for transmission and handling installations in pressure and suction systems for liquid and bulk substances. Not suitable for the transmission of steam and gases. The connector has a symmetrical design of the connection part. Material: bronze. Working pressure: 10 bar. Sealing: NBR rubber. Operating temperature: from -10°C to +80°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
GP-GOST2050050-B	GOST adapter 78 mm with BSP 2" thread, bronze	-	10	In stock	Enquiry
GP-GOST2050065-B	GOST adapter 78 mm with BSP 2.1/2", bronze	-	10	In stock	Enquiry
GP-GOST2070050-B	GOST adapter 95 mm with BSP 2" thread, bronze	-	10	In stock	Enquiry
GP-GOST2070065-B	GOST adapter 95 mm with BSP 2.1/2", bronze	-	10	In stock	Enquiry
GP-GOST2080050-B	GOST adapter 107 mm with BSP 2" thread, bronze	-	10	In stock	Enquiry
GP-GOST2080065-B	GOST adapter 107 mm with BSP 2.1/2", bronze	-	10	In stock	Enquiry
GP-GOST2080075-B	GOST adapter 107 mm with BSP 3" thread, bronze	-	10	In stock	Enquiry
GP-GOST2100100-B	GOST adapter 140 mm with BSP 4" thread, bronze	-	10	In stock	Enquiry
GP-GOST2110100-B	GOST adapter 143 mm with BSP 4" thread, bronze	-	10	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

GOST connector with internal thread intended for transmission and handling installations in pressure and suction systems for liquid and bulk substances. Not suitable for the transmission of steam and gases. The connector has a symmetrical design of the connection part. Material: bronze. Working pressure: 10 bar. Sealing: NBR rubber. Operating temperature: from -10°C to +80°C.