Is the Industrial bent nozzle for washing and cleaning with water BLUE NOZZLE, brass safe for use with hot water up to +65Â°C and what precautions should be taken?

Yes . the Industrial bent nozzle for washing and cleaning with water BLUE NOZZLE, brass is rated for use with hot water up to +65Â°C (continuous operation). However, observe these precautions: - Do not use for steam or temperatures above +65Â°C . the product is explicitly not intended for steam. - Special precautions when working with hot water: wear appropriate personal protective equipment (gloves, face shield) to prevent scalding if the nozzle is handled during or after use. - Allow the nozzle to cool before performing maintenance, disassembly or replacing parts; hot components (brass head, EPDM body) can cause burns. - Ensure all system seals, hoses and fittings are rated for the temperature and pressure in use (maximum working pressure 16 bar). - Check EPDM compatibility: while EPDM handles hot water, prolonged exposure at high temperatures can accelerate wear . inspect regularly for cracks or degradation. - Avoid sudden mechanical impacts when hot (stepping on it, running over) to prevent unexpected failure under thermal stress. - Follow correct connection (3/4" BSP) and do not exceed specified flow/pressure (13.5 l/min at 2.5 bar given as reference). These steps will help ensure safe operation within the nozzleâs specified limits.

Can the Industrial bent nozzle for washing and cleaning with water BLUE NOZZLE, brass be used with detergents or chemicals, and are there any compatibility warnings?

Industrial bent nozzle for washing and cleaning with water BLUE NOZZLE, brass: It is designed primarily for use with water. The body is EPDM rubber with a brass head, which offers good general chemical resistance, but the product description warns about special precautions with hot water and explicitly states it is not intended for steam. No specific detergent or chemical compatibility is provided-therefore avoid strong acids, alkalis, solvents, or oxidizers unless confirmed compatible with EPDM and brass. Maximum temperature 65Â°C and max pressure 16 bar should not be exceeded. If you plan to use detergents/chemicals, verify compatibility with EPDM rubber and brass, test on a small scale, and follow safety guidelines.

Does the Industrial bent nozzle for washing and cleaning with water BLUE NOZZLE, brass tolerate freezing temperatures or exposure to snow/ice?

The Industrial bent nozzle for washing and cleaning with water BLUE NOZZLE, brass is made of EPDM rubber with a brass head and is described as resistant to external damage (stepping on it, being run over by a vehicle, etc.). However, the product data does not explicitly state suitability for freezing temperatures or prolonged exposure to snow/ice. EPDM rubber has good cold-weather resistance compared with many elastomers, but freezing conditions can still make rubber stiffer and more brittle over time, especially if water remains inside and freezes. The nozzleâs maximum operating temperature is given (+65Â°C), but no minimum temperature or freeze/thaw tolerance is specified. Conclusion: There is no explicit guarantee that the Industrial bent nozzle for washing and cleaning with water BLUE NOZZLE, brass tolerates freezing temperatures or extended exposure to snow/ice. To avoid potential damage, drain water from the nozzle after use and store it protected from prolonged freezing conditions; contact the manufacturer for definitive cold-temperature specifications.

Industrial nozzle bent for washing and cleaning water BLUE NOZZLE, brass

All products, Low-pressure water spray guns/

Additional information

Nozzle for washing and cleaning water, which stream adjustable is at use thumb. Im greater radius bend, this stream water is stronger, a its shut-off occurs in moment return nozzle for position horizontal. nozzle is resistant to damage external (stepping on, driving over vehicle etc.). made with rubber EPDM, head made with brass. W case use with hot water, should maintain particularly agents caution. Not It is intended for steam! Connection: 3/4″ BSP female. Maximum Working pressure: 16 bar. Maximum Operating temperature: +65°C (work continuous). Flow rate: 13.5 l/min (at pressure 2.5 bar). weight: 280g. length: 230 mm.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
AK-BWNM045	Nozzle zginana BLUE NOZZLE, 3/4" BSP female, brass	-	16	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Nozzle for washing and cleaning water, which stream adjustable is at use thumb. Im greater radius bend, this stream water is stronger, a its shut-off occurs in moment return nozzle for position horizontal. nozzle is resistant to damage external (stepping on, driving over vehicle etc.). made with rubber EPDM, head made with brass. W case use with hot water, should maintain particularly agents caution. Not It is intended for steam! Connection: 3/4″ BSP female. Maximum Working pressure: 16 bar. Maximum Operating temperature: +65°C (work continuous). Flow rate: 13.5 l/min (at pressure 2.5 bar). weight: 280g. length: 230 mm.