Is the Metal-rubber gasket for UHP, 1000 bar compatible with quick couplings and adapters with external threads at full 1000 bar working pressure?

Yes . the Metal-rubber gasket for UHP, 1000 bar Format is designed specifically for use in high-pressure installations including quick couplings and adapters with external threads. Its stated working pressure "up to 1000 bar" means it is compatible with such couplings and threaded adapters at the full 1000 bar operating pressure, provided that the mating components (couplings, adapters, housings) and the installation meet the same pressure rating and are assembled per manufacturer instructions. Important: compatibility at 1000 bar requires that the quick couplings/adapters have matching dimensions and thread type, are rated for 1000 bar, and that installation (torque, surface finish, absence of damage) is correct. If any mating part is rated below 1000 bar or is improperly installed, the assembly cannot be guaranteed to hold 1000 bar safely.

Can Metal-rubber gasket for UHP, 1000 bar withstand repeated connection cycles in quick couplings and external-thread adapters?

Metal-rubber gasket for UHP, 1000 bar Format is designed for use in high-pressure installations including quick couplings and adapters with external threads, and its working pressure rating (up to 1000 bar) indicates suitability for repeated high-pressure service. However, ability to withstand repeated connection cycles depends on factors not specified in the brief description: gasket material composition and hardness, reinforcement design, surface finish of mating parts, assembly torque, pressure cycling profile, chemical exposure, temperature, and contamination. If the gasket uses reinforced metal-rubber construction engineered for cyclic sealing and the mating components are properly machined and assembled within recommended torque and environmental limits, it can endure multiple connection cycles. For a definitive answer and expected cycle life, consult manufacturer data sheets, test reports, or perform application-specific endurance testing.

Does the Metal-rubber gasket for UHP, 1000 bar require specific torque settings when used with quick couplings and external-thread adapters?

Yes. The Metal-rubber gasket for UHP, 1000 bar requires specific torque attention when used with quick couplings and external-thread adapters. Key points: - Manufacturer guidance: Always follow the coupling and adapter manufacturersâ recommended torque values. These values are determined to ensure proper gasket compression, sealing integrity and to avoid damage to the gasket or mating parts. - Correct compression: The Metal-rubber gasket for UHP, 1000 bar must be compressed to a defined rangeânot under-torqued (risking leaks) and not over-torqued (risking gasket deformation, loss of spring-back, or thread/face damage). Specified torque or axial clamping force from the equipment maker should be used where available. - Material and design sensitivity: Metal-rubber gaskets combine a soft seal element with a metal carrier; uneven or excessive torque can cause the rubber to extrude or the metal component to misalign, reducing effectiveness at ultra-high pressure (up to 1000 bar). - Use of torque tools: Use calibrated torque wrenches or controlled tightening procedures (e.g., torque sequence, progressive steps) to achieve uniform compression on quick couplings and threaded adapters. - Reuse and inspection: If reusing fittings, inspect the Metal-rubber gasket for UHP, 1000 bar for damage and follow any reuse limits from the supplier. Re-torqueing after initial pressurization may be recommended in some cases to account for initial seating. - If no torque is specified: If the quick coupling or adapter manufacturer does not provide a torque value, consult the gasket supplier for recommended clamping force or seek engineering guidance; avoid arbitrary high torque. In summary: Use the Metal-rubber gasket for UHP, 1000 bar with the specific torque/clamping recommendations provided by the coupling, adapter or gasket manufacturer, apply torque progressively and evenly with calibrated tools, and inspect/replace gaskets as required to maintain safe sealing at pressures up to 1000 bar.

Gasket metal-rubber for UHP, 1000 bar

All products, UHP adapters and accessories/

Additional information

A metal-rubber gasket for use in high-pressure installations (for quick couplings, adapters with a male thread). Working pressure: up to 1000 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
CJ-HP-199500061	Gasket metal-rubber 1/8", 1000 bar	-	-	In stock	Enquiry
CJ-HP-199500062	Gasket metal-rubber 1/4", 1000 bar	-	-	In stock	Enquiry
CJ-HP-199500064	Gasket metal-rubber 3/8", 1000 bar	-	-	In stock	Enquiry