Can the PUSH-ON self-clamping end with GZ BSPT, type YBZ130 be used with hose clamps or different hose types without causing damage?

No. The PUSH-ON self-clamping end with GZ BSPT, type YBZ130 is specifically designed for PUSH-ON self-clamping hoses and relies on a special groove profile matched to that hoseâs material, dimensions and braid structure to achieve secure clamping without additional hardware. Using it with other hose types or adding bands/clamps can damage the hose and compromise the connection. Use only the specified PUSH-ON hose and do not apply hose clamps or bands. Operating range: -40Â°C to +80Â°C; working pressure per the PUSH-ON hose specifications. Materials: galvanized carbon steel, brass, AISI 316 steel.

Is the PUSH-ON self-clamping end with GZ BSPT, type YBZ130 compatible with hoses other than the specified PUSH-ON hose?

No. The PUSH-ON self-clamping end with GZ BSPT, type YBZ130 is specifically designed for the PUSH-ON hose and its special groove profile, material compatibility and braid structure. It is mounted without clamps; using it with other hoses or adding clamps/bands can damage the hose and/or fitting. Use only with the specified PUSH-ON hose and observe the hoseâs working pressure and temperature range (-40Â°C to +80Â°C).

What maintenance is required for the PUSH-ON self-clamping end with GZ BSPT, type YBZ130 to ensure long-term sealing?

To ensure long-term sealing of the PUSH-ON self-clamping end with GZ BSPT, type YBZ130, perform the following maintenance and inspection steps: 1. Initial installation check - Verify that the hose is the correct PUSH-ON type intended for this fitting. Do not use other hose types. - Ensure the hose is pushed fully onto the fitting until it seats on the stop; incomplete assembly compromises the self-clamping grooves. 2. Regular visual inspections (recommended at intervals based on service duty, minimum every 3â6 months) - Check for external damage to the hose near the fitting (cuts, abrasions, kinks). - Inspect for any signs of fluid leakage at the fitting-hose interface. - Examine the fitting surface and thread (GZ BSPT) for corrosion, deformation or loose connection. 3. Functional checks - Monitor system pressure and temperature to ensure they remain within the PUSH-ON hose specifications and the specified operating range (-40 Â°C to +80 Â°C). Exceeding these limits can reduce sealing integrity. - After initial pressure tests or first hours of service, re-inspect the connection for signs of slippage or leakage. 4. Avoidances that preserve sealing - Never add external clamps, bands or hose clips to the assembled connection. these can deform the hose and damage the self-clamping grooves. - Do not use the fitting with hoses not designed for PUSH-ON fittings. 5. Cleaning and corrosion control - Keep threads and external surfaces free of dirt and contaminants that could impair seating or thread sealing. - For steel fittings, protect against corrosive environments; consider material selection (brass, galvanized steel, AISI 316) appropriate to fluid and environment to minimize corrosion risk. 6. Replacement criteria - Replace the hose end or entire hose if you observe persistent leakage, visible damage to the hose outer layer or braid, deformation of grooves, thread damage, or significant corrosion. - Replace fittings showing wear that could affect the groove profile or thread sealing. 7. Reassembly guidance - If disassembly is necessary, use new compliant PUSH-ON hose ends and follow manufacturer assembly procedures; do not attempt to reuse a hose that slipped off or was damaged. Following these steps will help maintain the mechanical bite of the special groove profile and the long-term sealing performance of the PUSH-ON self-clamping end with GZ BSPT, type YBZ130.

A self-clamping PUSH-ON end with a male BSP threadT, type YBZ130

All products, General purpose hoses/

Additional information

Material	SS – stainless steel
Standard length [m]	152.4

A PUSH-ON end with a male BSP threadT, type YBZ130, intended for a self-clamping hose designed for this type of end. Mounted onto the hose without the use of clamps or brackets. It has a special barb profile adapted to the material and dimensions of the PUSH-ON hose and the construction of its braid, causing the hose to clamp onto the barbs of the end. The end must not be used with other hoses or clamped with clamps or brackets, as this risks damaging the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specification of the PUSH-ON hose. Material: galvanised carbon steel, brass, AISI 316 steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-YBZ130-04-04	Fitting PUSH-ON 1/4" BSPT male, hose 1/4"	-	-	In stock	Enquiry
TI-YBZ130-04-04-MO	Fitting PUSH-ON 1/4" BSPT male, hose 1/4", MO58	-	-	In stock	Enquiry
TI-YBZ130-04-04-SS	Fitting PUSH-ON 1/4" BSPT male, hose 1/4", AISI 316L	-	-	In stock	Enquiry
TI-YBZ130-06-06	Fitting PUSH-ON 3/8" BSPT male, hose 3/8"	-	-	In stock	Enquiry
TI-YBZ130-06-06-MO	Fitting PUSH-ON 3/8" BSPT male, hose 3/8", MO58	-	-	In stock	Enquiry
TI-YBZ130-06-06-SS	Fitting PUSH-ON 3/8" BSPT male, hose 3/8", AISI 316L	-	-	In stock	Enquiry
TI-YBZ130-08-08	Fitting PUSH-ON 1/2" BSPT male, hose 1/2"	-	-	In stock	Enquiry
TI-YBZ130-08-08-MO	Fitting PUSH-ON 1/2" BSPT male, hose 1/2", MO58	-	-	In stock	Enquiry
TI-YBZ130-08-08-SS	Fitting PUSH-ON 1/2" BSPT male, hose 1/2", AISI 316L	-	-	In stock	Enquiry
TI-YBZ130-10-10	Fitting PUSH-ON 5/8" BSPT male, hose 5/8"	-	-	In stock	Enquiry
TI-YBZ130-10-10-MO	Fitting PUSH-ON 5/8" BSPT male, hose 5/8", MO58	-	-	In stock	Enquiry
TI-YBZ130-10-10-SS	Fitting PUSH-ON 5/8" BSPT male, hose 5/8", AISI 316L	-	-	In stock	Enquiry
TI-YBZ130-12-12	Fitting PUSH-ON 3/4" BSPT male, hose 3/4"	-	-	In stock	Enquiry
TI-YBZ130-12-12-MO	Fitting PUSH-ON 3/4" BSPT male, hose 3/4", MO58	-	-	In stock	Enquiry
TI-YBZ130-12-12-SS	Fitting PUSH-ON 3/4" BSPT male, hose 3/4", AISI 316L	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

A PUSH-ON end with a male BSP threadT, type YBZ130, intended for a self-clamping hose designed for this type of end. Mounted onto the hose without the use of clamps or brackets. It has a special barb profile adapted to the material and dimensions of the PUSH-ON hose and the construction of its braid, causing the hose to clamp onto the barbs of the end. The end must not be used with other hoses or clamped with clamps or brackets, as this risks damaging the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specification of the PUSH-ON hose. Material: galvanised carbon steel, brass, AISI 316 steel.