What maintenance is required for the Hydraulic spool valve, operated by hand lever, type YFM55 to ensure reliable operation and longevity?

Hydraulic spool valve, operated by hand lever, type YFM55 . maintenance for reliable operation and longevity: - Regular visual inspection: check body, lever, linkages and mounting for cracks, corrosion, loose bolts and proper alignment. - Cleanliness: keep exterior free of dirt, mud and debris; protect lever area and centering springs from contamination. - Hydraulic fluid: use recommended fluid, maintain proper cleanliness (filtering to recommended micron level) and replace per system schedule. Monitor fluid for contamination, water, or degradation and maintain tank breathers and filters. - Seals and O-rings (NBR): periodically inspect for wear, hardening or leaks; replace seals showing damage or after long service/after fluid change. - Sliders (hardened steel): check for smooth, backlash-free movement; if sticking or scoring occurs, inspect for contamination and wear. Lightly lubricate sliding surfaces only if specified by manufacturer; avoid excess lubricant that attracts dirt. - Safety valve (type C, set 140 bar): test relief setting and operation periodically; recalibrate or replace if drift or leakage occurs. - Pressure checks: verify system working pressure does not exceed max 315 bar and return pressure remains below 25 bar. - Temperature considerations: avoid prolonged exposure outside -20Â°C to +80Â°C; when operating near limits, inspect seals and fluid more frequently. - Functional testing: cycle valve through full travel, verify centering springs return spool to neutral, check for internal leakage, improper detents or failure to hold position. - Scheduled overhaul: based on hours and operating conditions, perform disassembly, clean internal passages, replace worn sliders/seals and inspect body bores for wear or scoring. - Documentation: keep maintenance records, note valve hours, leak incidents and repairs. Follow manufacturer service intervals and procedures for any repair or calibration to ensure safety and warranty compliance.

How do I troubleshoot sticking or slow response in the Hydraulic spool valve, operated by hand lever, type YFM55?

Check basic conditions first: fluid level, contamination and viscosity (must match -20Â°C to +80Â°C range). For Hydraulic spool valve, operated by hand lever, type YFM55 inspect external lever and centering springs for wear or misalignment. Steps: 1. Clean: remove dirt/debris around spool opening and ports; flush circuit if contamination suspected. 2. Filter and fluid: replace/clean hydraulic filters and change fluid if degraded or contaminated. 3. Check return and system pressures: ensure max working pressure â¤315 bar and return â¤25 bar; verify safety valve (type C) set at 140 bar and functioning (stuck or leaking valve can cause sluggish response). 4. Inspect spool and bore: disassemble and examine sliders (hardened steel) and castâiron body for scoring, pitting or corrosion; polish minor scoring, replace sliders if damaged. 5. Seals: replace NBR seals if swollen, hardened or cut. 6. Centering springs: test/replace weak or broken springs to restore neutral centering. 7. Temperature effects: at low temp fluid thickening can slow response-warm system or use correct viscosity fluid. 8. Reassemble with correct clearances and test for leaks and smooth operation. If problem persists, consult manufacturer or fit replacement parts.

Can the Hydraulic spool valve, operated by hand lever, type YFM55 be used in mobile applications with frequent vibration?

Hydraulic spool valve, operated by hand lever, type YFM55 Format can be used in mobile applications with frequent vibration, but with some important considerations. Why it can be suitable: - The valve is designed for mobile equipment (cranes, lifts, construction machines, agricultural equipment), which implies basic suitability for mobile and vibrating environments. - Robust materials (cast iron body, hardened steel sliders) provide mechanical durability against shock and wear. - Centering springs and manual lever control with type 1 sliders are common and reliable in mobile hydraulics. Limitations and cautions: - Sealing is NBR (nitrile). NBR performs well for many hydraulic oils and moderate temperatures, but prolonged shock/vibration combined with contaminants, high temperatures near the upper limit (+80Â°C), or aggressive fluids may accelerate wear or leakage. Consider FKM/fluorocarbon seals if exposure to higher temps or aggressive media is expected. - Maximum working pressure is 315 bar and the standard safety valve is set to 140 bar. Ensure system pressures and pressure spikes under vibration/shock remain within these limits; otherwise adjust/set the safety valve appropriately. - Return line max pressure 25 bar must be respected; frequent vibration can cause pressure fluctuationsâconfirm tank/return line design minimizes pulsation/backpressure. - Mounting and fixation: vibration-prone use demands firm, vibration-damped mounting, correct torque on fasteners, and possibly additional anti-vibration measures (rubber/damping pads, support brackets) to prevent loosening or fatigue. - Service and maintenance: plan for more frequent inspection of mounting, seals, and spool movement to detect wear or contamination from vibration-induced ingress. Recommendation: Hydraulic spool valve, operated by hand lever, type YFM55 Format is broadly suitable for mobile, vibrating applications if installed and maintained properly, system pressures and temperatures stay within specified limits, seals and safety valve settings are reviewed for the specific operating environment, and vibration-damping mounting and maintenance practices are applied.

Directional valve hydraulic spool, pilot-operated hand lever, type YFM55

All products, Directional control valves/

Additional information

Maximum operating temperature [°C]	80
Minimum operating temperature [°C]	-20

A monoblock Directional valve spool YFM55 pilot-operated hand lever of centering springs. Intended for hydraulic systems of cranes, lifts, construction and agricultural machinery, etc.. As standard, equipped with a type C safety valve (set to 140 bar) and type 1 spools. Material: cast iron (body), steel hardened (spools). Sealing: NBR. Maximum working pressure: 315 bar. Maximum return pressure: 25 bar. Operating temperature: from -20°C to +80°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TL-YFM55-1-C-1	Hydraulic directional valve YFM55, 1-section with a valve overflow	-	315	In stock	Enquiry
TL-YFM55-2-C-11	Hydraulic directional valve YFM55, 2-section with a valve overflow	-	315	In stock	Enquiry
TL-YFM55-3-C-111	Hydraulic directional valve YFM55, 3-section with a valve overflow	-	315	In stock	Enquiry
TL-YFM55-4-C-1111	Hydraulic directional valve YFM55, 4-section with a valve overflow	-	315	In stock	Enquiry
TL-YFM55-5-C-11111	Hydraulic directional valve YFM55, 5-section with a valve overflow	-	315	In stock	Enquiry
TL-YFM55-6-C-111111	Hydraulic directional valve YFM55, 6-section with a valve overflow	-	315	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

A monoblock Directional valve spool YFM55 pilot-operated hand lever of centering springs. Intended for hydraulic systems of cranes, lifts, construction and agricultural machinery, etc.. As standard, equipped with a type C safety valve (set to 140 bar) and type 1 spools. Material: cast iron (body), steel hardened (spools). Sealing: NBR. Maximum working pressure: 315 bar. Maximum return pressure: 25 bar. Operating temperature: from -20°C to +80°C.