Is the Water gun with rear trigger, stainless steel, AKBO, blue compatible with food-grade systems given its Viton (FDA) sealing and EPDM shields?

Water gun with rear trigger, stainless steel, AKBO, blue: based on the provided description, it appears largely compatible with food-grade systems but with some important caveats. Why compatible: - Viton sealing (FDA) indicates the primary seal material meets FDA-approved fluorocarbon elastomer standards, suitable for many food and beverage contact applications and resistant to oils and high temperatures (up to the stated +95Â°C). - Stainless steel body is standard for hygienic, food-compatible equipment. - EPDM rubber shields provide chemical and temperature resistance commonly acceptable in food environments for non-sealing covers or protective parts. Caveats and checks required before use in food-grade systems: - Confirm FDA compliance documentation: obtain the manufacturerâs FDA/food-contact certification for the specific Viton compound used (not all Viton grades are FDA-cleared). - Verify EPDM compliance: ensure the EPDM shields are explicitly certified for food contact (FDA or EU food-contact regulations), since the description only names the material. - Assess full assembly: any other internal components, lubricants, or coatings must be food-grade and documented. - Temperature and pressure limits: maximum operating temperature +95Â°C and max pressure 24 bar are acceptable depending on your process; ensure these match your systemâs conditions. - Connection hygiene: 1/2" NPT is common but may require sanitary fittings or adaptors to meet hygienic/cleanability standards in your installation. - Cleaning and CIP compatibility: confirm the gun tolerates your cleaning agents and CIP procedures. Conclusion: Water gun with rear trigger, stainless steel, AKBO, blue can be suitable for food-grade use if you obtain explicit food-contact certifications for the Viton and EPDM parts and verify all other materials and assembly details meet your regulatory and sanitary requirements.

Can the Water gun with rear trigger, stainless steel, AKBO, blue handle repeated sterilization at 95Â°C without degrading Viton (FDA) seals?

Based on the provided specification, the Water gun with rear trigger, stainless steel, AKBO, blue has Viton sealing (FDA) and a maximum operating temperature of +95Â°C. Standard FDA-grade Viton (FKM) compounds are generally rated for continuous service up to about 200Â°C and short-term exposure beyond that; 95Â°C is well within typical Viton limits. Therefore repeated sterilization at 95Â°C is unlikely to chemically degrade Viton seals, provided the sterilization medium is compatible (e.g., hot water/steam or compatible cleaning agents) and cycle durations and chemical exposures are not extreme. Also consider that repeated thermal cycling and aggressive detergents or oxidizers can shorten seal life; EPDM shields may have different resistance. In summary: Water gun with rear trigger, stainless steel, AKBO, blue should tolerate repeated 95Â°C sterilization, but validate with supplier or perform life-cycle testing under your exact sterilization conditions to ensure long-term seal integrity.

Does the Water gun with rear trigger, stainless steel, AKBO, blue require specific maintenance for EPDM shields and Viton (FDA) seals?

Water gun with rear trigger, stainless steel, AKBO, blue does not require unusual or complicated maintenance for its EPDM shields and Viton (FDA) seals, but basic care will maximize life and performance: - Routine inspection: Regularly check EPDM shields and Viton seals for cuts, abrasions, hardening, swelling, or chemical attack. Inspect before use and during scheduled maintenance intervals depending on frequency of use. - Cleaning: Rinse seals and surrounding areas with fresh water after use, especially if the gun handled chemicals, hot water (up to its max operating temperature +95Â°C), or abrasive particulates. Avoid aggressive solvents that can degrade Viton or EPDM. - Compatible media: EPDM is resistant to hot water and many alkaline cleaners but is vulnerable to most hydrocarbons and oils. Viton (FKM, FDA grade) is highly chemical- and heat-resistant but can be affected by certain amines or ketones. Avoid prolonged exposure to incompatible fluids to prevent premature aging. - Temperature and pressure limits: Operate within the specified maximums (24 bar, +95Â°C). Excessive pressure or temperature accelerates seal wear. - Lubrication and assembly: If reassembly or seal replacement is needed, use lubricants compatible with EPDM and Viton (water-based or manufacturer-recommended FDA-compatible lubricants). Do not use petroleum-based greases on EPDM. - Storage: Store the Water gun with rear trigger, stainless steel, AKBO, blue in a clean, cool, shaded area away from direct sunlight and ozone sources to reduce seal degradation. - Replacement: Replace seals at the first signs of leakage or visible deterioration. Keep manufacturer-approved EPDM and FDA Viton spare parts to maintain sealing performance. Following these standard precautions will ensure reliable sealing performance and prolong the service life of the EPDM shields and Viton (FDA) seals.

Water gun with rear trigger, stainless steel, AKBO, blue

All products, Low-pressure water spray guns/

Additional information

AKBO water gun made of stainless steel with a rear trigger. EPDM rubber shields, Viton sealing (FDA). It features an adjustable outlet nozzle, smooth flow regulation, and a trigger lock. Connection: 1/2″ NPT. Maximum working pressure: 24 bar. Maximum operating temperature: +95°C. Weight: approx. 0.87 kg. Flow rate: 28 l/min (5 bar), 58 l/min (15 bar).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
AK-RBT01-BL-U	AKBO water gun, GW 1/2" NPT, rear trigger, AISI 316, blue	-	24	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

AKBO water gun made of stainless steel with a rear trigger. EPDM rubber shields, Viton sealing (FDA). It features an adjustable outlet nozzle, smooth flow regulation, and a trigger lock. Connection: 1/2″ NPT. Maximum working pressure: 24 bar. Maximum operating temperature: +95°C. Weight: approx. 0.87 kg. Flow rate: 28 l/min (5 bar), 58 l/min (15 bar).