Is the Water washing and cleaning nozzle, brass, AKBO Heavy Duty safe to use with hot water up to 80Â°C, and what precautions are required since it is not intended for steam?

Yes . the Water washing and cleaning nozzle, brass, AKBO Heavy Duty is rated for use with hot water up to +80Â°C. However, because it is explicitly not intended for steam, observe these precautions: - Do not use with steam or in any application where steam could be present or generated. Steam exceeds the intended use and may damage seals or the mechanism. - Ensure incoming water temperature does not exceed +80Â°C at the nozzle. Monitor system temperatures and install thermal cutoffs or mixing valves as needed to prevent temperature spikes. - EPDM seals withstand hot water but degrade if exposed to oils, solvents, or aggressive chemicals; avoid such fluids. - Allow for thermal expansion and avoid rapid temperature cycling which can stress brass parts and seals. - Inspect seals and covers regularly for hardening, cracking or leaks; replace worn EPDM components promptly. - Use the correct connection (GW 1/2" BSP) and keep working pressure within the specified maximum (16 bar). Higher pressures increase risk when combined with high temperatures. - Operate the rotating head and shutoff carefully when hot; use protective gloves and avoid direct contact with hot surfaces. Following these measures will maintain safe operation for hot-water use up to 80Â°C while preventing damage that could result from steam exposure.

Can the Water washing and cleaning nozzle, brass, AKBO Heavy Duty be used with pressurized hot water systemsâwhat safety steps should I follow?

Yes - the Water washing and cleaning nozzle, brass, AKBO Heavy Duty can be used with pressurized hot water systems, but not for steam. Follow these safety steps: - Do not exceed max operating temperature +80Â°C and max working pressure 16 bar. - Flush and inspect before use; ensure EPDM seals and covers show no damage or aging. - Use appropriate handle version or secure grip (AK-MSHH4-BK is without handle). - Open flow slowly by rotating the head to avoid water hammer and sudden temperature/pressure surges; the head can fully shut off flow when tightened. - Wear thermal-protective gloves, face shield and protective clothing to guard against scalding. - Ensure all connections are properly tightened to GW 1/2" BSP and check for leaks at operating temperature. - Do not use with steam or above rated temperature/pressure; if unsure, consult supplier or safety data.

Can the Water washing and cleaning nozzle, brass, AKBO Heavy Duty be used with hot water above 80Â°C or near-steam conditions?

No. The Water washing and cleaning nozzle, brass, AKBO Heavy Duty is not suitable for use with steam or in nearâsteam conditions. Its maximum operating temperature is +80Â°C, and the product description explicitly states âNot intended for steam.â The mechanism is brass with EPDM rubber covers and seals; EPDM degrades more rapidly above its rated temperature range and is not steamâcompatible. If you need to work with water hotter than 80Â°C or with steam, choose a nozzle rated for higher temperatures and steam service to avoid seal failure, leakage, or safety hazards.

Nozzle for washing and cleaning water, brass, AKBO Heavy Duty

All products, Low-pressure water spray guns/

Additional information

Nozzle Intended for washing and cleaning water, which stream adjustable is thanks to swivel the head. Flow rate can be completely closed through solid tightening the head. mechanism made with brass, cover and the gasket with rubber EPDM. Available with handle in color blue, red and white ( AK-MSHH4-BK – version without handle, 1/2″ BSP male). W case use with hot water, should maintain particularly agents caution. Not It is intended for steam! Connection: 1/2″ BSP female. maximum Working pressure: 16 bar. Maximum Operating temperature: +80°C. Flow rate: 110 l/min (5 bar), 150 l/min (16 bar).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AK-MSH03-BL	Nozzle AKBO HEAVY DUTY, 1/2" BSP female, brass, black, A bracket blue	-	16	In stock	Enquiry
AK-MSH03-R	Nozzle AKBO HEAVY DUTY, 1/2" BSP female, brass, black, A bracket red	-	16	In stock	Enquiry
AK-MSH03-W	Nozzle AKBO HEAVY DUTY, 1/2" BSP female, brass, black, A bracket white	-	16	In stock	Enquiry
AK-MSHH4-BK	Nozzle AKBO HEAVY DUTY, without handle, 1/2" BSP male, brass, black	-	16	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Nozzle Intended for washing and cleaning water, which stream adjustable is thanks to swivel the head. Flow rate can be completely closed through solid tightening the head. mechanism made with brass, cover and the gasket with rubber EPDM. Available with handle in color blue, red and white ( AK-MSHH4-BK – version without handle, 1/2″ BSP male). W case use with hot water, should maintain particularly agents caution. Not It is intended for steam! Connection: 1/2″ BSP female. maximum Working pressure: 16 bar. Maximum Operating temperature: +80°C. Flow rate: 110 l/min (5 bar), 150 l/min (16 bar).