Is the Hot water gun insulated with a 40 cm lance, stainless steel, AKBO HEAVY DUTY safe for use above 95Â°C or with steam?

Hot water gun insulated with a 40 cm lance, stainless steel, AKBO HEAVY DUTY is NOT safe for use above 95Â°C or with steam. The product specification states an operating temperature up to +95Â°C and explicitly notes it is not intended for steam. Although made from AISI 316 stainless steel with Teflon-air insulation, EPDM seals, and a protective trigger cover, exceeding the rated temperature or exposing the unit to steam risks seal failure, material degradation, and unsafe operation. Use above 95Â°C or with steam is contraindicated; follow the manufacturer limits and exercise special caution when using hot water near the maximum rating.

Can the Hot water gun insulated with a 40 cm lance, stainless steel, AKBO HEAVY DUTY be used safely with chemicals or detergents at high temperatures?

Hot water gun insulated with a 40 cm lance, stainless steel, AKBO HEAVY DUTY can be used with hot water up to +95Â°C and is built from corrosionâresistant AISI 316 and stainless steel components, with EPDM seals and Teflon air insulation. However: it is not intended for steam and the manufacturer warns that use with hot water requires special caution. EPDM seals resist many detergents and mild alkalis, but can be attacked by strong acids, ketones, and some solvents. Teflon and AISI 316 offer good chemical resistance, yet compatibility depends on the specific chemical, concentration and temperature. For safe use with highâtemperature chemicals/detergents, verify the chemical compatibility with AISI 316, EPDM and PTFE at elevated temperature, ensure concentration is suitable, maintain below 95Â°C, and follow manufacturer guidance and PPE. If in doubt, contact the manufacturer or choose components rated for the specific chemical.

Does the Hot water gun insulated with a 40 cm lance, stainless steel, AKBO HEAVY DUTY require special maintenance after use at temperatures near 95Â°C?

Hot water gun insulated with a 40 cm lance, stainless steel, AKBO HEAVY DUTY: Yes. after using near the maximum operating temperature (â95Â°C) you should perform some basic, regular maintenance to preserve safety and longevity. Recommended steps: - Allow the unit to cool before handling or storing to avoid burns and to prevent thermal stress on seals and insulation. - Rinse internal passages with clean water to remove deposits, especially if water quality is hard or contains debris. Drain thoroughly to avoid stagnation. - Inspect EPDM linings and seals for softening, swelling, cracks or leaks; replace any damaged seals promptly (EPDM is heat-resistant but can degrade over time at high temps). - Check the AISI 316 body, stainless pusher and lance for corrosion, pitting or scale; clean external surfaces and the nozzle if flow is reduced. - Verify the Teflon-air insulation and trigger protective cover are intact and not deformed or burned; replace damaged insulation/protection. - Test the flow-regulating nozzle and trigger mechanism for smooth operation; lubricate moving parts with compatible materials if needed (avoid oils that attack EPDM or PTFE). - Inspect the 1/2" BSP connection and fittings for leaks and tighten or reseal as required. - Store in a dry, ventilated place away from direct sunlight and chemicals that could attack EPDM or Teflon. Do not use for steam; avoid exposing seals and components repeatedly above recommended temperature. Regular checks after high-temperature use will help prevent premature wear and ensure safe operation.

Hot water gun insulated with a 40 cm lance, stainless steel, AKBO HEAVY DUTY

All products, Low-pressure water spray guns/

Additional information

AKBO HEAVY DUTY hot water gun made of AISI 316 steel, with Teflon-air insulation and a protective cover for the trigger. Equipped with a 40 cm lance with a handle and a nozzle with flow regulation. Not intended for steam. Use with hot water requires special caution. Body material: AISI 316 steel. Pusher material: stainless steel. Linings and seals made of ethylene-propylene rubber (EPDM). Connection: 1/2″ BSP. Working pressure: 24 bar. Flow rate: 75 l/min. Operating temperature: up to +95°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
AK-RHP02-R-L40	AKBO hot water gun, GW 1/2" BSP, insulated, lance 40 cm, AISI 316, red	-	24	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

AKBO HEAVY DUTY hot water gun made of AISI 316 steel, with Teflon-air insulation and a protective cover for the trigger. Equipped with a 40 cm lance with a handle and a nozzle with flow regulation. Not intended for steam. Use with hot water requires special caution. Body material: AISI 316 steel. Pusher material: stainless steel. Linings and seals made of ethylene-propylene rubber (EPDM). Connection: 1/2″ BSP. Working pressure: 24 bar. Flow rate: 75 l/min. Operating temperature: up to +95°C.