Is the Connector "T" made of acetal copolymer (POM) suitable for use with gases, liquids and vacuum systems at pressures up to 10 bar?

Yes. The Connector "T" made of acetal copolymer (POM) is suitable for use with gases, liquids and vacuum systems at pressures up to 10 bar. It is specifically designed for control systems and installations for the transport of gases and liquids, as well as vacuum applications, and its working pressure rating is up to 10 bar.

Can Connector "T" made of acetal copolymer withstand chemicals commonly used in pneumatic and hydraulic systems?

Connector "T" made of acetal copolymer (POM) offers good general chemical resistance and is commonly used in pneumatic and many low-aggressive hydraulic applications. It resists water, mineral oils, greases, alcohols, and many dilute acids and bases, and is suitable for gases, liquids and vacuum systems up to 10 bar as specified. However, POM is attacked by strong oxidizers (e.g., nitric acid, chlorine), concentrated acids/alkalis, aromatic and chlorinated hydrocarbons (e.g., benzene, toluene, trichloroethylene) and some polar solvents. For systems using aggressive hydraulic fluids, solvents, or strong chemicals, verify compatibility with the specific fluid and operating temperature; if in doubt, choose a connector made of a more chemically resistant material.

Does Connector "T" in acetal copolymer (POM) require special maintenance for long-term use under 10 bar?

Connector "T" made from acetal copolymer (POM) does not require any extraordinary maintenance for long-term use under the specified working pressure of up to 10 bar, provided normal operating conditions are met. Recommended practices to ensure reliable long-term performance: - Routine inspection: periodically check for visible wear, cracks, deformation, or chemical attack, especially at barbed or threaded connection points and seals. - Cleanliness: keep the Connector "T" and mating tubing/fittings free of dirt, debris and particulates that can abrade surfaces or impair sealing. - Proper installation: use compatible tubing and correct insertion depth; avoid overstretching or forcing connections that can damage the barbs or create leaks. - Avoid excessive mechanical stress: minimize bending, torsion or vibration at the Connector "T" to prevent fatigue or stress risers. - Chemical compatibility: ensure transported fluids/gases and cleaning agents are compatible with acetal copolymer; avoid strong oxidizers, concentrated acids/bases or solvents known to swell or degrade POM. - Temperature limits: operate within the recommended temperature range for POM; avoid prolonged exposure to temperatures near or above its glass transition or melting range which can reduce strength. - Pressure cycling: if the system experiences frequent pressure spikes or rapid cycling, monitor for signs of fatigue; consider pressure dampening if necessary. - Seals and fittings: replace any O-rings or soft seals regularly as per their material guideline; ensure threaded seals or tape are applied correctly without over-torquing. Following these standard precautions and periodic inspections will keep Connector "T" in acetal copolymer functioning reliably under 10 bar for long-term use.

Connector “T”, acetal copolymer

All products, Low-pressure fittings and adapters/

Additional information

Material	P – material (plastic)

T-connector for hose, type NA. Designed for use in control systems, in installations for the transport of gases and liquids, in vacuum systems, etc. Working pressure: up to 10 bar. Material: acetal copolymer (POM).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
NA-7600000003	T connector DN2.5, 3 mm hose	3	10	In stock	Enquiry
NA-7600000004	T connector DN2.7, 4 mm hose	4	10	In stock	Enquiry
NA-7600000005	T connector DN3, 5 mm hose	5	10	In stock	Enquiry
NA-7600000006	T connector DN4, hose 6 mm	6	10	In stock	Enquiry
NA-7600000007	T connector DN5, 7 mm hose	6	10	In stock	Enquiry
NA-7600000008	T connector DN5.6, hose 8 mm	8	10	In stock	Enquiry
NA-7600000010	T connector DN7, hose 10 mm	10	10	In stock	Enquiry
NA-7600000012	T connector DN8.6, hose 12 mm	12	10	In stock	Enquiry
NA-7600000013	T connector DN8.6, 13 mm hose	12	10	In stock	Enquiry
NA-7600000014	T connector DN10, hose 14 mm	14	10	In stock	Enquiry
NA-7600000015	T connector DN11, hose 15 mm	16	10	In stock	Enquiry
NA-7600000016	T connector DN12, hose 16 mm	16	10	In stock	Enquiry
NA-7600000019	T connector DN15, hose 19 mm	20	10	In stock	Enquiry
NA-7600000025	T connector DN21, hose 25 mm	25	10	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

T-connector for hose, type NA. Designed for use in control systems, in installations for the transport of gases and liquids, in vacuum systems, etc. Working pressure: up to 10 bar. Material: acetal copolymer (POM).