How do I install the WIRE CLIP wire spring clamp (spring steel) on low-pressure hoses using universal pliers?

To install the WIRE CLIP wire spring clamp (spring steel) on low-pressure hoses using universal pliers, follow these steps: 1. Select the correct WIRE CLIP wire spring clamp size so its internal diameter at rest provides adequate elastic pressure on the hose once installed. 2. Slide the clamp onto the hose over the fitting end (or position it nearby before mounting). 3. Grip the two clamp arms with universal pliers and press them together firmly.this opens the clampâs diameter. 4. While holding the arms compressed, place the opened clamp over the hose so that its inner ring sits evenly around the hose, just beyond the fitting or at the required sealing point. 5. Release the pliers slowly, allowing the WIRE CLIP wire spring clamp to contract and apply uniform elastic pressure to the hose. 6. Check that the clamp seats evenly, is centered over the connection, and that the hose compresses without deformation or gaps. If needed, remove and reposition by repeating the steps. Safety note: Wear eye protection and ensure the clamp is not overstretched beyond its elastic range.

Can the WIRE CLIP wire spring clamp, spring steel be reused after removal from a low-pressure hose?

Yes - the WIRE CLIP wire spring clamp, spring steel can be reused after removal from a low-pressure hose, provided it is not visibly deformed, cracked, corroded, or permanently stretched. Because itâs made of galvanized spring steel, it relies on elastic tension to maintain a secure seal; if the clampâs shape and springiness remain intact after removal, it will retain sufficient elastic pressure to be refitted onto a hose within its specified diameter range. Always inspect for damage and test fit: if the internal diameter and arm tension return the clamp to the correct closed position and it grips the hose firmly without gaps, reuse is acceptable. If any loss of elasticity or visible damage is present, replace the clamp.

What hose diameter range is best suited for the WIRE CLIP wire spring clamp, spring steel?

The WIRE CLIP wire spring clamp, spring steel is designed to fasten low-pressure hoses that fall within the clampâs specified diameter range. Because installation is performed by compressing the clamp arms with universal pliers, you should select a hose whose outside diameter lies within the clampâs stated minâmax range; during fitting you can expand the clamp slightly to place it over a hose whose diameter is just above the clampâs maximum, relying on the spring steelâs elastic recovery to provide proper sealing pressure. In practice, choose a clamp whose internal diameter range closely matches the hose OD; do not use a clamp for hoses significantly smaller or larger than that range to avoid leaks or clamp failure.

WIRE CLIP wire spring clamp, spring steel

All products, Clamps for mounting ends/

Additional information

Material	CS – steel (cast iron)

Spring clamp with double wire designed for quick fastening of low-pressure hoses. It is made of galvanized spring steel. Installation with universal pliers by pressing the clamp’s arms together, allowing the clamp to be placed on a hose with a diameter slightly larger than the maximum (from the range of clamp diameters: the internal diameter of the spring clamp ensuring appropriate elastic pressure).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AB-02016012	Spring clamp 7.3÷7.8 mm	-	-	In stock	Enquiry
AB-02016020	Spring clamp 7.8÷8.3 mm	-	-	In stock	Enquiry
AB-02016039	Spring clamp 8.3÷8.8 mm	-	-	In stock	Enquiry
AB-02016047	Spring clamp 8.8÷9.3 mm	-	-	In stock	Enquiry
AB-02016055	Spring clamp 9.3÷9.9 mm	-	-	In stock	Enquiry
AB-02016063	Spring clamp 9.8÷10.4 mm	-	-	In stock	Enquiry
AB-02016071	Spring clamp 10.4÷11 mm	-	-	In stock	Enquiry
AB-02016080	Spring clamp 11÷11.6 mm	-	-	In stock	Enquiry
AB-02016098	Spring clamp 11.6÷12.3 mm	-	-	In stock	Enquiry
AB-02016100	Spring clamp 12.1÷13.1 mm	-	-	In stock	Enquiry
AB-02016119	Spring clamp 12.9÷13.6 mm	-	-	In stock	Enquiry
AB-02016127	Spring clamp 13.6÷14.4 mm	-	-	In stock	Enquiry
AB-02016135	Spring clamp 14.4÷15.1 mm	-	-	In stock	Enquiry
AB-02016143	Spring clamp 14.8÷15.9 mm	-	-	In stock	Enquiry
AB-02016151	Spring clamp 15.9÷16.8 mm	-	-	In stock	Enquiry
AB-02016160	Spring clamp 16.8÷17.7 mm	-	-	In stock	Enquiry
AB-02016178	Spring clamp 17.7÷18.7 mm	-	-	In stock	Enquiry
AB-02016186	Spring clamp 18.7÷19.6 mm	-	-	In stock	Enquiry
AB-02016194	Spring clamp 19.6÷20.6 mm	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Spring clamp with double wire designed for quick fastening of low-pressure hoses. It is made of galvanized spring steel. Installation with universal pliers by pressing the clamp’s arms together, allowing the clamp to be placed on a hose with a diameter slightly larger than the maximum (from the range of clamp diameters: the internal diameter of the spring clamp ensuring appropriate elastic pressure).