Is the Hose coupling, AISI 304 steel, type CND suitable for repeated assembly and disassembly with standard stainless steel clamps?

Yes. The Hose coupling, AISI 304 steel, type CND is suitable for repeated assembly and disassembly with standard stainless steel clamps. The product description explicitly states it is intended for rubber and plastic industrial hoses, is designed for assembly using straps or clamps, and is specified "for multiple assembly and disassembly." Made from AISI 304 stainless steel, it resists corrosion and holds up well under repeated clamping cycles, provided clamps are appropriately sized and tightened to recommended torque. For best results and longevity, use compatible stainless steel clamps (grade 304 or higher), avoid overtightening that could deform the hose or connector, and inspect sealing surfaces and clamp tension periodically.

Can Hose coupling, AISI 304 steel, type CND be safely used with rubber and plastic hoses when tightened with band clamps?

Yes. Hose coupling, AISI 304 steel, type CND is intended for use with rubber and plastic industrial hoses and is made of AISI 304 stainless steel. It is designed specifically for assembly using straps or band clamps and for multiple assembly/disassembly cycles. When properly sized and tightened with appropriate band clamps, it can be safely used with rubber and plastic hoses. Ensure correct diameter match, use clamps rated for the application, tighten to manufacturer torque recommendations, and inspect regularly for wear, corrosion or slippage to maintain a safe seal.

Does Hose coupling, AISI 304 steel, type CND resist corrosion from common industrial chemicals?

Hose coupling, AISI 304 steel, type CND (corrugated connector intended for rubber and plastic industrial hoses made of AISI 304 steel; designed for assembly using straps or clamps; for multiple assembly and disassembly) offers good general corrosion resistance but has limitations against many common industrial chemicals. AISI 304 (EN 1.4301) is an austenitic stainless steel with good resistance to atmospheric corrosion, water, and many mild chemicals (alkalis, some organic acids, and certain dilute inorganic acids). For typical industrial fluids like clean water, wastewater, mild detergents, oils, greases, and many food-grade substances, Hose coupling, AISI 304 steel, type CND will generally resist corrosion adequately when used in appropriate conditions (moderate temperatures, no strong mechanical abrasion, and with proper cleaning and drainage). However, AISI 304 is vulnerable to: - Chloride-induced corrosion (pitting and crevice corrosion): chloride-containing media (saline solutions, brines, bleach/NaOCl, seawater, some cooling waters) can attack 304, especially at elevated temperatures or in crevices (hose-to-coupling interfaces, clamps). - Strong oxidizing acids and halogens: concentrated nitric, sulfuric, hydrochloric acids, and halogenated compounds can cause rapid attack. - Hydrogen sulfide and sour environments: can produce sulfide stress cracking or general corrosion in some conditions. - High-temperature corrosive environments: performance declines with temperature and concentration. Because the CND coupling is corrugated and intended for repeated assembly/disassembly with clamps or straps, crevice sites and mechanical wear can increase susceptibility to localized corrosion. If service involves chlorides, aggressive acids, high temperatures, or abrasive fluids, consider upgrading to a higher-alloy stainless (e.g., AISI 316/316L with molybdenum for better chloride resistance) or a compatible specialty material. For borderline cases, verify chemical compatibility with actual fluid composition, temperature, concentration, and duty cycle; perform testing or consult a corrosion engineer. Conclusion: Hose coupling, AISI 304 steel, type CND resists many common mild industrial chemicals but is not suitable for chloride-rich, strongly acidic, sulfide-containing, or high-temperature corrosive environments without further evaluation or a more resistant material.

Hose coupling, AISI 304 steel, type CND

All products, Low-pressure fittings and adapters/

Additional information

Material	SS – stainless steel

CND corrugated connector intended for rubber and plastic industrial hoses made of AISI 304 steel. Designed for assembly using straps or clamps. For multiple assembly and disassembly. Material: AISI 304 steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AC-CND-025-SS	1/4" hose connector, AISI 304	6	10	In stock	Enquiry
AC-CND-038-SS	3/8" hose connector, AISI 304	10	10	In stock	Enquiry
AC-CND-050-SS	1/2" hose connector, AISI 304	12	10	In stock	Enquiry
AC-CND-058-SS	5/8" hose connector, AISI 304	16	10	In stock	Enquiry
AC-CND-075-SS	3/4" hose connector, AISI 304	20	10	In stock	Enquiry
AC-CND-100-SS	1" hose connector, AISI 304	25	10	In stock	Enquiry
AC-CND-1000-SS	10" hose connector, AISI 304	250	10	In stock	Enquiry
AC-CND-125-SS	Connector for hoses 1.1/4", AISI 304	32	10	In stock	Enquiry
AC-CND-138-SS	Hose connector 1.3/8", AISI 304	35	10	In stock	Enquiry
AC-CND-150-SS	Hose connector 1.1/2", AISI 304	40	10	In stock	Enquiry
AC-CND-200-SS	2" hose connector, AISI 304	50	10	In stock	Enquiry
AC-CND-250-SS	Hose connector 2.1/2", AISI 304	65	10	In stock	Enquiry
AC-CND-300-SS	3" hose connector, AISI 304	75	10	In stock	Enquiry
AC-CND-400-SS	4" hose connector, AISI 304	100	10	In stock	Enquiry
AC-CND-500-SS	5" hose connector, AISI 304	125	10	In stock	Enquiry
AC-CND-600-SS	6" hose connector, AISI 304	150	10	In stock	Enquiry
AC-CND-800-SS	8" hose connector, AISI 304	200	10	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

CND corrugated connector intended for rubber and plastic industrial hoses made of AISI 304 steel. Designed for assembly using straps or clamps. For multiple assembly and disassembly. Material: AISI 304 steel.