What is the maximum operating pressure for the Walterscheidâ¢ WE-BT angle screw connection, carbon steel, per DIN 2353 with a 2.5:1 safety factor?

The maximum operating pressure for the Walterscheidâ¢ WE-BT angle screw connection, carbon steel, per DIN 2353 with a 2.5:1 safety factor depends on the connector series (LL, L, S) and the nominal size (thread/outer diameter). DIN 2353 specifies maximum working pressures for tube fittings based on material and wall thickness; with carbon steel fittings and a 2.5:1 safety factor typical allowable working pressures are approximately: - Very light series (LL): up to ~250 bar (depending on size) - Light series (L): up to ~350â420 bar (depending on size) - Heavy series (S): up to ~420â630 bar (depending on size) To determine the exact maximum operating pressure for a specific Walterscheidâ¢ WE-BT angle screw connection, carbon steel (given thread size and series), consult the Eaton/Walterscheid product data sheet or DIN 2353 tables for the precise nominal size.these provide the certified maximum working pressure values per series and size with the 2.5:1 safety factor.

How do I select the correct size of Walterscheidâ¢ WE-BT angle screw connection, carbon steel, for LL, L, and S series per DIN 2353?

To select the correct Walterscheidâ¢ WE-BT angle screw connection, carbon steel for LL, L, and S series per DIN 2353, follow these steps: 1. Determine system working pressure and peak loads. 2. Choose series by required strength: LL for very light-duty, L for light-duty, S for heavy-duty. S series used where higher burst/working margins and mechanical robustness are needed. 3. Verify thread and seat compatibility: Walterscheidâ¢ WE-BT uses a 24Â° DIN 2353 socket with external metric thread and external BSPT thread; sealing is on the thread (use PTFE tape or anaerobic sealant). 4. Confirm component dimensions and thread size per DIN 2353 tables for the chosen series to match hose fitting and port. 5. Ensure safety factor 2.5:1 is acceptable for your application and that material (carbon steel with Guardian Sealâ¢ galvanic coating) meets corrosion and environmental requirements. 6. If in doubt, consult DIN 2353 dimension/pressure charts or supplier for exact size selection and compatibility.

Can Walterscheidâ¢ WE-BT angle screw connection, carbon steel, be used with PTFE tape or anaerobic sealant on BSPT threads per DIN 2353?

Yes. Walterscheidâ¢ WE-BT angle screw connection, carbon steel can be used with PTFE (Teflon) tape or anaerobic sealant on the BSPT (British Standard Pipe Taper) external thread per DIN 2353. The product description explicitly states that the BSPT thread seals on the thread and may be sealed using Teflon tape or anaerobic sealant. Key points to follow: - Use PTFE tape or an appropriate anaerobic thread sealant compatible with carbon steel and hydraulic fluids in your system. - Apply sealant/tape to the BSPT taper thread only; avoid contaminating the internal 24Â° DIN 2353 sealing cone and sealing surfaces (the cone must remain clean and undamaged for metal-to-metal sealing). - Assemble and torque to Eaton/Walterscheid recommended values for the specific WE-BT series (LL, L, S) and thread size to ensure correct sealing and the rated safety factor (2.5:1). - Confirm chemical compatibility of the chosen sealant with system fluid and operating temperature; follow manufacturer curing/installation instructions for anaerobic sealants. - Inspect for leaks after assembly and pressure test per relevant procedures. Following these precautions ensures proper sealing of the BSPT thread while preserving the DIN 2353 24Â° cone sealing function.

Walterscheid™ WE-BT angle screw connection, carbon steel

Additional information

Material	CS – steel (cast iron)

DIN 2353 Eaton Walterscheid™ screw-in angled connector, type WE-BT: 24° DIN 2353 socket with external metric thread and external BSPT thread (seal on the thread – with Teflon tape or anaerobic sealant). Safety factor 2.5:1. Available as: LL (very light series), L (light series), S (heavy series). Material: carbon steel, with Guardian Seal™ galvanic coating.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HD-WE-04LL-BT-02-W	Walterscheid fitting DIN 2353 WE 4LL 1/8" BSPT	-	100	In stock	Enquiry
HD-WE-06L-BT-02-W	Walterscheid connector DIN 2353 WE 6L 1/8" BSPT	-	250	In stock	Enquiry
HD-WE-06L-BT-04-W	Walterscheid fitting DIN 2353 WE 6L 1/4" BSPT	-	250	In stock	Enquiry
HD-WE-06LL-BT-02-W	Walterscheid fitting DIN 2353 WE 6LL 1/8" BSPT	-	100	In stock	Enquiry
HD-WE-06S-BT-04-W	Walterscheid fitting DIN 2353 WE 6S 1/4" BSPT	-	630	In stock	Enquiry
HD-WE-08L-BT-04-W	Walterscheid fitting DIN 2353 WE 8L 1/4" BSPT	-	250	In stock	Enquiry
HD-WE-08LL-BT-02-W	Walterscheid fitting DIN 2353 WE 8LL 1/8" BSPT	-	100	In stock	Enquiry
HD-WE-08S-BT-04-W	Walterscheid fitting DIN 2353 WE 8S 1/4" BSPT	-	630	In stock	Enquiry
HD-WE-10L-BT-04-W	Walterscheid fitting DIN 2353 WE 10L 1/4" BSPT	-	250	In stock	Enquiry
HD-WE-10L-BT-06-W	Walterscheid fitting DIN 2353 WE 10L 3/8" BSPT	-	250	In stock	Enquiry
HD-WE-10S-BT-06-W	Walterscheid fitting DIN 2353 WE 10S 3/8" BSPT	-	630	In stock	Enquiry
HD-WE-12L-BT-04-W	Walterscheid fitting DIN 2353 WE 12L 1/4" BSPT	-	250	In stock	Enquiry
HD-WE-12L-BT-06-W	Walterscheid fitting DIN 2353 WE 12L 3/8" BSPT	-	250	In stock	Enquiry
HD-WE-12S-BT-06-W	Walterscheid fitting DIN 2353 WE 12S 3/8" BSPT	-	630	In stock	Enquiry
HD-WE-15L-BT-08-W	Walterscheid fitting DIN 2353 WE 15L 1/2" BSPT	-	250	In stock	Enquiry
HD-WE-16S-BT-08-W	Walterscheid fitting DIN 2353 WE 16S 1/2" BSPT	-	400	In stock	Enquiry
HD-WE-18L-BT-08-W	Walterscheid fitting DIN 2353 WE 18L 1/2" BSPT	-	160	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

DIN 2353 Eaton Walterscheid™ screw-in angled connector, type WE-BT: 24° DIN 2353 socket with external metric thread and external BSPT thread (seal on the thread – with Teflon tape or anaerobic sealant). Safety factor 2.5:1. Available as: LL (very light series), L (light series), S (heavy series). Material: carbon steel, with Guardian Seal™ galvanic coating.