Is the Metric male threaded end, 24Â° taper, carbon steel, type SA compatible with standard low-pressure sanitary, fuel, and air hose assemblies with external steel braid?

Yes. The Metric male threaded end, 24Â° taper, carbon steel, type SA Format is compatible with standard lowâpressure sanitary, fuel, and air hose assemblies that have external steel braid. It is specifically designed for lowâpressure rubber, nonâreinforced and textileâreinforced plastic hoses with external steel braid, providing a 24Â° cone seal suitable for sanitary fittings, fuel systems and air systems. Material and finish (carbon steel, galvanized) are consistent with typical hose assembly requirements for those applications. Ensure hose and fitting sizes, pressure ratings and any industryâspecific cleanliness or corrosionâresistance standards are matched before installation.

Can the Metric male threaded end, 24Â° taper, carbon steel, type SA be used with textile-reinforced plastic hoses without braid damage?

Yes. The Metric male threaded end, 24Â° taper, carbon steel, type SA Format is designed for use with low-pressure rubber and non-reinforced and textile-reinforced plastic hoses with external steel braid. When fitted correctly, it can be used with textile-reinforced plastic hoses without damaging the braid. Ensure compatibility by verifying hose inner/outer dimensions match the fitting, use the correct assembly method (appropriate ferrule/crimping or clamping per hose manufacturer), and avoid over-tightening which can abrade textile fibers. Properly matched components and correct installation will prevent braid damage and ensure reliable sealing and service life.

Does the Metric male threaded end, 24Â° taper, carbon steel, type SA require specific assembly tools or torque values?

Metric male threaded end, 24Â° taper, carbon steel, type SA Format. does it require specific assembly tools or torque values? Yes. although Metric male threaded end, 24Â° taper, carbon steel, type SA Format is designed for relatively low-pressure rubber and nonâreinforced/textileâreinforced plastic hoses with external steel braid, proper assembly practices are important to ensure leakâfree cone sealing and mechanical integrity. Key guidance: - Cone sealing requires correct alignment and full engagement of the 24Â° tapered seat; use calibrated torque to compress the cone against its mating seat evenly. - Use appropriate wrenches sized for the hex flats of the fitting; avoid pliers or pipe wrenches that can deform the fitting. - Where available, follow the fitting manufacturerâs recommended torque values. If manufacturer data is not available, use standard torque tables for metric male threads of the same diameter and grade, adjusted for steel and for whether threads are lubricated or galvanised (galvanised surfaces typically increase friction. reduce target torque or use a lubrication factor). - Typical practice: assemble hand tight, then apply a measured additional fraction of full torque (often 1/4 to 1/2 of specified torque for softâseating tapered fittings) while checking for correct seating and hose alignment. For pressurized systems, perform a pressure/leak test after assembly. - Use proper hose clamp or crimp tooling if the fitting design requires swaging or clamping of the braid/hose end. Textileâreinforced and nonâreinforced hoses may require specific swaging dies or clamps sized to the fitting and hose. Safety notes: - Overâtorquing can deform the 24Â° taper, damage threads, or cause leaks; underâtorquing risks incomplete sealing. - When in doubt, consult the fitting/hose manufacturerâs assembly instructions or a qualified technician for exact torque values and tooling recommendations. In summary, Metric male threaded end, 24Â° taper, carbon steel, type SA Format benefits from correct tools and controlled torque. follow manufacturer specs or standard metric thread torque tables and use proper wrenches and hose assembly/swaging equipment to ensure safe, leakâfree joints.

Metric male threaded end, 24° taper, carbon steel, type SA

All products, Low-pressure fittings and adapters/

Additional information

Material	CS – steel (cast iron)

SA type end fitting with external metric thread, 24° cone sealing, designed for low-pressure rubber and non-reinforced and textile-reinforced plastic hoses, with external steel braid. Commonly used in flexible hoses for sanitary fittings, fuel systems, air systems, etc. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
EC-110205	SA GZ M10x1 end, 24° cone, (hose 5.5 mm)	5	30	In stock	Enquiry
EC-110206	SA GZ M12x1.5 end, 24° cone, (hose 5.5 mm)	6	30	In stock	Enquiry
EC-110208	SA GZ M14x1.5 end, 24° cone, (hose 7.5 mm)	8	30	In stock	Enquiry
EC-110210	SA GZ M16x1.5 end, 24° cone, (hose 9 mm)	10	30	In stock	Enquiry
EC-110212	SA GZ M18x1.5 end, 24° cone, (hose 11.5 mm)	12	30	In stock	Enquiry
EC-110215	SA GZ M22x1.5 end, 24° cone, (hose 14.5 mm)	14	30	In stock	Enquiry
EC-110216	SA GZ M22x1.5 fitting, 24° angle, (tube 16 mm, hose 14.5 mm)	14	30	In stock	Enquiry
EC-110217	SA GZ M26x1.5 end, 24° cone, (hose 14.5 mm)	14	30	In stock	Enquiry
EC-110218	SA GZ M26x1.5 end, 24° cone, (hose 17 mm)	18	30	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

SA type end fitting with external metric thread, 24° cone sealing, designed for low-pressure rubber and non-reinforced and textile-reinforced plastic hoses, with external steel braid. Commonly used in flexible hoses for sanitary fittings, fuel systems, air systems, etc. Material: carbon steel, galvanized.