Is the Bendable lance for high-pressure washer, inlet GZ M22x1.5, stainless steel, type ST-85 compatible with all pressure washers up to 210 bar and how do I attach it?

Bendable lance for high-pressure washer, inlet GZ M22x1.5, stainless steel, type ST-85 is rated for working pressures up to 210 bar, so it is compatible with pressure washers whose maximum working pressure does not exceed 210 bar. Do not use it with machines that exceed that limit. How to attach it: 1. Ensure the washer is off and depressurised. 2. Check threads: the lance inlet is male GZ M22x1.5. Your pressure washer hose or gun must have a matching female (internal) G1/4? . wait: verify the washerâs outlet fitting. The lance outlet is GW 1/4" NPT (female) for the downstream connection. 3. If your gun/hose has a matching female M22x1.5 thread, screw the lance inlet into it by hand, then tighten with an appropriate spanner.do not overtighten. 4. If threads differ, use a correct adapter (e.g., from your washerâs outlet to GZ M22x1.5) rated for â¥210 bar and compatible materials. 5. Fit any required sealing (PTFE tape or thread sealant) on NPT threads only, following manufacturer guidance; do not seal tapered threads incorrectly. 6. After attachment, slowly pressurise the system, check for leaks, and test the bending adjustment (20Â°â140Â°) while keeping hands clear of the spray. If unsure about thread compatibility or adapters, consult your washerâs manual or supplier to avoid mismatched threads and unsafe use.

Can the Bendable lance for high-pressure washer, inlet GZ M22x1.5, stainless steel, type ST-85 be safely used on vehicle roofs and undercarriages?

Yes. the Bendable lance for high-pressure washer, inlet GZ M22x1.5, stainless steel, type ST-85 can be safely used on vehicle roofs and undercarriages provided you follow proper precautions and operating limits. Why itâs suitable - Designed specifically for cleaning hard-to-reach surfaces such as vehicle undercarriages and roofs; its adjustable bending angle (20Â°â140Â°) enables access where a straight lance cannot reach. - Constructed from stainless steel, suitable for automotive cleaning environments. - Rated for working pressures up to 210 bar and temperatures up to +150Â°C, which covers typical high-pressure washer conditions for vehicle cleaning. Safety and usage recommendations - Ensure your pressure washer does not exceed 210 bar and the fluid temperature does not exceed +150Â°C. - Check thread compatibility (inlet GZ M22x1.5 / outlet GW 1/4" NPT) with your equipment before use and use appropriate adapters if needed. - Inspect the lance for damage, corrosion, or loose fittings before each use. - Use appropriate spray nozzles and maintain a safe distance to avoid paint damage, bending of panels, or injury; start at lower pressure or wider spray pattern and test on a small area. - Wear PPE (eye protection, gloves, protective clothing) and follow manufacturer and local safety guidelines when working under vehicles or on elevated surfaces. - Secure the vehicle (handbrake, wheel chocks) and ensure stable footing or use proper lifts/platforms when cleaning roofs or undercarriages. In summary: The Bendable lance for high-pressure washer, inlet GZ M22x1.5, stainless steel, type ST-85 is intended for and appropriate for vehicle roofs and undercarriages when used within its pressure/temperature ratings and with standard safety and operational precautions.

Bendable lance for high-pressure washer, inlet GZ M22x1.5, stainless steel, type ST-85

Q: Can the Bendable lance for high-pressure washer, inlet GZ M22x1.5, stainless steel, type ST-85 be used at temperatures up to +150Â°C?

Yes. Bendable lance for high-pressure washer, inlet GZ M22x1.5, stainless steel, type ST-85 can be used at temperatures up to +150Â°C. The product specification lists operating temperature up to +150Â°C, working pressure up to 210 bar, and stainless steel construction suitable for such temperatures.

All products, Guns for high-pressure washers/

Additional information

Bending lance type ST-85 designed for high-pressure washers. Smooth adjustment of the bending angle of the lance from 20° to 140° allows for cleaning hard-to-reach surfaces, e.g., vehicle undercarriages and roofs, tanks, etc. Connections: (inlet) GZ M22x1.5 / (outlet) GW 1/4″ NPT. Working pressure: up to 210 bar. Operating temperature: up to +150°C. Material: stainless steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
RM-200085260	Bending lance, GZ M22x1.5/GW 1/4" NPT, L = 600 mm, SS	-	210	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Bending lance type ST-85 designed for high-pressure washers. Smooth adjustment of the bending angle of the lance from 20° to 140° allows for cleaning hard-to-reach surfaces, e.g., vehicle undercarriages and roofs, tanks, etc. Connections: (inlet) GZ M22x1.5 / (outlet) GW 1/4″ NPT. Working pressure: up to 210 bar. Operating temperature: up to +150°C. Material: stainless steel.