Can the Waxing gun with 0.7 l. plastic tank, 125 series handle fluids with viscosity higher than water and still maintain consistent flow through its 3 mm fixed nozzle?

Short answer: Possibly, but not reliably for fluids significantly more viscous than water. Reasoning: The Waxing gun with 0.7 l. plastic tank, 125 series is described as an aluminum gun with a fixed 3 mm nozzle that "utilizes vacuum to draw low-viscosity fluid from the tank" and has an adjustable flow. That wording and the vacuum feed indicate the system is optimized for low-viscosity liquids. A 3 mm fixed nozzle and operating pressure 2â6 bar can push thicker fluids to some extent (up to the limits of pump/vacuum, nozzle resistance and air supply), but the vacuum draw and small nozzle become limiting factors as viscosity rises. Higher-viscosity fluids increase suction effort required, reduce flow rate, risk inconsistent pulsing, clogging or incomplete atomization, and may demand higher pressure, larger nozzle, or positive-feed pump. Practical guidance: If your fluid is only slightly more viscous than water (e.g., light oils or low-viscosity wax blends), the Waxing gun with 0.7 l. plastic tank, 125 series may maintain usable flow at the upper end of operating pressure (closer to 6 bar) and warm side of operating temperature (+50Â°C). For medium-to-high viscosities you should test under working conditions. For consistent flow with substantially thicker fluids, use a device with a positive-feed pump, larger nozzle, or designed for high-viscosity materials.

Does the Waxing gun with 0.7 l. plastic tank, 125 series handle solvents safely at 6 bar without damaging the aluminum body?

Yes. The Waxing gun with 0.7 l. plastic tank, 125 series is specified for operating pressures up to 6 bar (operating range 2â6 bar) and a maximum pressure of 10 bar, so using it at 6 bar is within rated limits. It draws lowâviscosity fluids by vacuum and has a plastic tank; the body is aluminum and the operating temperature range is +5Â°C to +50Â°C. However, compatibility with solvents depends on the specific solventâs chemical aggressiveness toward aluminum and the plastic tank material-if the solvent is known to attack aluminum or the tank material, damage may occur despite pressure ratings. For safe longâterm use, verify chemical compatibility of your solvent with aluminum and the tank material or consult the manufacturer.

Is the Waxing gun with 0.7 l. plastic tank, 125 series compatible with food-safe fluids at 4 bar?

The Waxing gun with 0.7 l. plastic tank, 125 series is not explicitly specified as food-safe in the provided description. Key points from the description: - Tank material: plastic (0.7 l). material type and food-grade certification are not stated. - Fluid handling: uses vacuum to draw low-viscosity fluids through a fixed Ã 3 mm nozzle with adjustable flow. - Operating pressure range: 2â6 bar (maximum 10 bar). 4 bar falls within the operating range. - Operating temperature: +5Â°C to +50Â°C. compatible with many food-safe fluids if temperature limits are met. Conclusion: Mechanically, the Waxing gun with 0.7 l. plastic tank, 125 series can operate at 4 bar and handle low-viscosity fluids. However, without confirmation that the plastic tank, internal seals, nozzle and other wetted parts are made of food-grade, FDA/EFSA-approved materials and that the unit is designed for sanitary/food-industry cleaning, it should not be assumed safe for use with food fluids. For food applications, obtain manufacturer certification or documentation verifying food-grade materials and hygienic suitability before use.

Waxing gun with 0.7 l. plastic tank, 125 series

All products, Special air guns/

Additional information

Aluminum gun with a fixed nozzle Ø 3 mm, with flow rate adjustment. Utilizes vacuum to draw low-viscosity fluid from the tank. Tank: plastic with a capacity of 0.7 l. Nozzle diameter: 3 mm. Maximum pressure: 10 bar. Operating pressure: 2 ÷ 6 bar. Operating temperature: from +5°C to +50°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
EW-125241	Waxing gun, 1 l tank, plastic, DN7.2 plug	-	10	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Aluminum gun with a fixed nozzle Ø 3 mm, with flow rate adjustment. Utilizes vacuum to draw low-viscosity fluid from the tank. Tank: plastic with a capacity of 0.7 l. Nozzle diameter: 3 mm. Maximum pressure: 10 bar. Operating pressure: 2 ÷ 6 bar. Operating temperature: from +5°C to +50°C.