Does the Electrically controlled hydraulic spool valve, type 4/3, NG10 support 315 bar on P/A/B and 160 bar on T across all listed control voltages?

Yes. According to the provided description of the Electrically controlled hydraulic spool valve, type 4/3, NG10 Format, the maximum operating pressures are specified as 315 bar for ports P, A, and B, and 160 bar for port T. Those pressure ratings are stated alongside the list of available control voltages (12 V DC, 24 V DC, 110 V AC, 220 V AC) without any qualification, so they apply across all listed control voltages.

Is the Electrically controlled hydraulic spool valve, type 4/3, NG10 compatible with panel mounting cutouts and standard mounting screws?

Yes. Electrically controlled hydraulic spool valve, type 4/3, NG10 Format is intended for panel mounting and is standardly supplied with mounting screws and O-rings, so it is compatible with panel mounting cutouts and standard mounting screws.

Can the Electrically controlled hydraulic spool valve, type 4/3, NG10 operate safely between -20Â°C and +80Â°C under load?

Electrically controlled hydraulic spool valve, type 4/3, NG10 Format can operate safely between -20Â°C and +80Â°C under load, provided that the installation and operating conditions respect the specified limits. The given data specify an operating temperature range of -20Â°C to +80Â°C and maximum pressures (315 bar on P, A, B; 160 bar on T), indicating the valve is designed for use under load within that temperature window. Key points to ensure safe operation: - Use within the stated temperature range (-20Â°C to +80Â°C). Outside this range seals (NBR), electrical components (coil, diodes), and materials may suffer degradation or altered properties. - Maintain pressures at or below the maximum ratings (315/160 bar). Overpressure combined with extreme temperatures increases risk of leakage or component failure. - Ensure correct control voltage (12/24 V DC or 110/220 V AC) and proper electrical connections; diodes on couplings indicate power status but do not substitute for correct wiring or protection. - Consider viscosity and fluid properties at temperature extremes: hydraulic fluid must remain within its recommended viscosity and temperature limits to ensure proper spool movement and avoid cavitation or sluggish response. - Ambient vs. fluid temperature: confirm both hydraulic fluid and ambient conditions fall within limits; heat build-up under load may raise local temperatures. - Regular inspection and maintenance of O-rings (NBR), mounting, and electrical insulation is recommended, especially after exposure to temperature cycling. Conclusion: Yes. when used with appropriate hydraulic fluid, within the specified pressure and voltage limits, and maintained per recommendations, the Electrically controlled hydraulic spool valve, type 4/3, NG10 Format is rated for safe operation between -20Â°C and +80Â°C under load.

Electrically controlled hydraulic spool valve, type 4/3, NG10

All products, Valves and plate adapters/

Additional information

Maximum operating temperature [°C]	80
Minimum operating temperature [°C]	-20

Sliding valve, type 4/3, electrically controlled with centering springs, intended for panel mounting. Used in hydraulic systems of industrial machines. Standardly supplied with O-rings and mounting screws. couplings are equipped with diodes indicating power status. Material: cast iron (body), hardened steel (slider). Sealing: NBR. Maximum operating pressure: 315 bar (ports P, A, B), 160 bar (port T). Available for the following control voltages: 12 V DC, 24 V DC, 110 V AC, or 220 V AC. Operating temperature: from -20°C to +80°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TL-NG10-E-24DC	Hydraulic distributor NG10, type 4/3, control 24V DC	-	315	In stock	Enquiry
TL-NG10-G-24DC	Hydraulic distributor NG10, type 4/3, control 24V DC	-	315	In stock	Enquiry
TL-NG10-H-24DC	Hydraulic distributor NG10, type 4/3, control 24V DC	-	315	In stock	Enquiry
TL-NG10-J-24DC	Hydraulic distributor NG10, type 4/3, control 24V DC	-	315	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Sliding valve, type 4/3, electrically controlled with centering springs, intended for panel mounting. Used in hydraulic systems of industrial machines. Standardly supplied with O-rings and mounting screws. couplings are equipped with diodes indicating power status. Material: cast iron (body), hardened steel (slider). Sealing: NBR. Maximum operating pressure: 315 bar (ports P, A, B), 160 bar (port T). Available for the following control voltages: 12 V DC, 24 V DC, 110 V AC, or 220 V AC. Operating temperature: from -20°C to +80°C.