Does the Carbon steel pressure sleeve, type FC ensure proper compression of the inch pipe to the coupling when installed in the nut?

Yes. The Carbon steel pressure sleeve, type FC, when placed in the nut, ensures proper compression of the inch pipe to the coupling. Its carbon steel construction and galvanised finish provide the strength and corrosion resistance needed to maintain a secure, compressive fit between the pipe and fitting.

How does the Carbon steel pressure sleeve, type FC installed in the nut improve sealing between the inch pipe and the coupling?

The Carbon steel pressure sleeve, type FC installed in the nut improves sealing by concentrating and transmitting the nutâs compressive force evenly around the inch pipe where it enters the coupling. When the nut is tightened, the sleeve deforms slightly and bites or presses against both the tube OD and the coupling ID, creating a continuous metal-to-metal contact zone. This controlled compression compensates for minor surface irregularities, forms a tight mechanical seal, and prevents axial movement or leakage under pressure. Galvanized carbon steel gives the sleeve sufficient strength and corrosion resistance to maintain that seal over time.

Can Carbon steel pressure sleeve, type FC withstand galvanization and maintain pipe compression over time?

Yes. a Carbon steel pressure sleeve, type FC can be galvanized and still maintain pipe compression over time, but several conditions must be met to ensure long-term performance. Key points: - Galvanization compatibility: Carbon steel is suitable for hot-dip galvanizing or electro-galvanizing. A properly applied zinc coating protects the steel from corrosion while preserving the sleeveâs mechanical dimensions and functionality. - Mechanical performance: The pressure sleeveâs role is to create and retain a mechanical compression of the inch pipe into the fitting. Galvanization, when done correctly, adds a thin protective layer that does not significantly alter the sleeveâs ability to deform and hold grip; however, excessive zinc buildup or uneven coating in the seating/compression surfaces can impair fit and clamping action. - Surface preparation and coating quality: For reliable long-term compression, the sleeve should be galvanized to a controlled thickness with post-coating inspection to ensure mating surfaces remain within tolerance. Mechanical cleaning and proper masking (if required) before galvanizing help avoid interference at critical contact areas. - Corrosion and galvanic considerations: Galvanizing reduces corrosion risk for the sleeve itself. If the mating fitting or pipe materials differ (e.g., copper or stainless), consider galvanic corrosion risk; in most common steel-to-steel assemblies this is not an issue. Use compatible materials or insulating measures where dissimilar metals are present. - Installation and maintenance: Correct installation torque and assembly procedure are essential. over- or under-tightening can compromise compression regardless of galvanization. Periodic inspection in aggressive environments is advisable to confirm retained compression and absence of coating degradation. Conclusion: When manufactured and galvanized to appropriate standards, a Carbon steel pressure sleeve, type FC will withstand galvanization and can maintain pipe compression over time. Ensure proper coating control, dimensional tolerances, compatible mating materials, and correct installation for best results.

Carbon steel pressure sleeve, type FC

Additional information

Material	CS – steel (cast iron)
Standard length [m]	2

The pressure sleeve, type FC, placed in the nut, allows for proper compression of the inch pipe to the fitting (coupling). Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HJ-FC-04	1/4" bushing	-	-	In stock	Enquiry
HJ-FC-06	3/8 bushing	-	-	In stock	Enquiry
HJ-FC-08	Sleeve 1/2"	-	-	In stock	Enquiry
HJ-FC-12	Sleeve 3/4	-	-	In stock	Enquiry
HJ-FC-16	Sleeve 1	-	-	In stock	Enquiry
HJ-FC-20	Sleeve 1.1/4"	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

The pressure sleeve, type FC, placed in the nut, allows for proper compression of the inch pipe to the fitting (coupling). Material: carbon steel, galvanized.