Is Collet for 1SC hydraulic hoses, AISI 316 steel, type Z1TC (PH) compatible with fittings PH without machining?

Yes. Collet for 1SC hydraulic hoses, AISI 316 steel, type Z1TC (PH) is compatible with PH fittings without machining. The product description explicitly states it is a Z1TC (PH) clamping sleeve for rubber hydraulic hoses type 1SC, designed for use with hydraulic fittings (PH) and that installation requires no machining. Material (AISI 316) and outer diameter (D1) are provided for correct selection, so ensure the sleeveâs D1 matches your hose/fitting dimensions before assembly.

Can Collet for 1SC hydraulic hoses, AISI 316 steel, type Z1TC (PH) be installed on PH fittings without special tools or machining?

Yes. Collet for 1SC hydraulic hoses, AISI 316 steel, type Z1TC (PH) can be installed on PH fittings without special tools or machining. The Z1TC (PH) clamping sleeve for rubber hydraulic hoses type 1SC is designed for installation with no machining required and is intended for use with hydraulic fittings (PH). Ensure correct matching to the hose outer diameter (D1) and follow manufacturer installation instructions for secure assembly.

Can Collet for 1SC hydraulic hoses, AISI 316 steel, type Z1TC (PH) be reused after removal without machining?

Yes. Collet for 1SC hydraulic hoses, AISI 316 steel, type Z1TC (PH) can be reused after removal without machining, provided certain conditions are met. Because the Z1TC (PH) clamping sleeve is designed for rubber hydraulic hoses type 1SC and specified as âinstallation - no machining required,â it is manufactured to tight tolerances and robust AISI 316 stainless steel. Reuse is acceptable if: - The collet shows no visible damage: no cracks, deep scratches, bends, deformation or corrosion that could affect clamping integrity. - The sealing and contact surfaces are smooth and free of gouges, nicks or scoring that would prevent proper hose seating or cause leaks. - Threads (if present) and mating faces are undamaged and clean. - Internal bore has not been excessively worn or distorted by prior use. - The associated hose and fitting are in good condition and compatible with reuse (no embedded debris or permanent set compromising fit). - Reassembly follows correct installation procedure and required torque/assembly checks. If any of the above defects are present, replace the Collet for 1SC hydraulic hoses, AISI 316 steel, type Z1TC (PH) rather than reuse. When in doubt, replace to ensure safety and reliable hydraulic performance.

Collet for 1SC hydraulic hoses, AISI 316 steel, type Z1TC (PH)

All products, Fittings for high-pressure hoses/

Additional information

Material	SS – stainless steel

Z1TC (PH) clamping sleeve for rubber hydraulic hoses type 1SC. Installation – no machining required. Use for hydraulic fittings (PH). Diameter D1 [mm] – outer diameter. Material: AISI 316 steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-Z1TC-04-SS-PH	Hose sleeve 1SC 1/4", AISI 316	6	-	In stock	Enquiry
TI-Z1TC-05-SS-PH	Hose sleeve 1SC 5/16", AISI 316	8	-	In stock	Enquiry
TI-Z1TC-06-SS-PH	Hose sleeve 1SC 3/8", AISI 316	10	-	In stock	Enquiry
TI-Z1TC-08-SS-PH	Hose sleeve 1SC 1/2", AISI 316	12	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Z1TC (PH) clamping sleeve for rubber hydraulic hoses type 1SC. Installation – no machining required. Use for hydraulic fittings (PH). Diameter D1 [mm] – outer diameter. Material: AISI 316 steel.