Can High temperature sealant 310ml PYROSEALANT be used on surfaces exposed to gasoline or diesel fuel?

No. High temperature sealant 310ml PYROSEALANT should not be used on surfaces exposed to gasoline or diesel fuel. The product description explicitly advises avoiding contact with gasoline or diesel. Although PYROSEALANT is thermally resistant (â59Â°C to +287Â°C, temporarily to +538Â°C) and cures to a non-sticky state, its formulation (amorphous silica, polydimethylsiloxane, iron oxide and a catalyst) may degrade, swell, or be chemically attacked by fuels, compromising sealing performance and safety. Use a fuel-resistant sealant specifically rated for hydrocarbon exposure.

Is High temperature sealant 310ml PYROSEALANT suitable for use on electrical connections or wiring?

High temperature sealant 310ml PYROSEALANT should be used with caution on electrical connections or wiring. Its silicone-based, thermally resistant formulation and nonâconductive ingredients (amorphous silica, polydimethylsiloxane, iron oxide, catalyst) suggest it is not inherently conductive, and its temperature range (-59Â°C to +287Â°C, briefly to +538Â°C) is suitable for highâheat environments. However: the product description does not state electrical insulation properties, dielectric strength, or certification for electrical use. It may release fumes during curing and requires good ventilation; avoid contact with fuels. Recommendation: do not use on live electrical contacts without confirming electrical insulation ratings and manufacturer guidance; if needed, apply only to de-energized, cleaned connections and verify compatibility with insulation requirements or choose a product specifically rated for electrical applications.

Can High temperature sealant 310ml PYROSEALANT be applied on hot exhaust manifolds while the engine is running?

No. you should not apply High temperature sealant 310ml PYROOSEALANT directly onto a hot exhaust manifold while the engine is running. Why: - The product is a thermally resistant semi-liquid paste that cures to a non-sticky state in 10â15 minutes and fully cures in about 18 hours. Proper curing requires controlled conditions and time; applying to a surface that is already hot and moving (running engine) will interfere with correct curing. - Although it withstands operating temperatures from -59Â°C to +287Â°C and temporarily up to +538Â°C, these ratings describe the cured materialâs service limits, not safe application conditions. High surface temperatures and engine heat cycles can prevent adhesion, cause premature skinning or runoff, or produce harmful fumes if applied to extremely hot metal. - Safety: the product should be used in well-ventilated areas and contact with fuels must be avoided. Applying to a running engine raises inhalation and fire risks from vapors and proximity to fuel lines. Recommended procedure: 1. Turn off the engine and let the manifold cool to a safe, moderate temperature (ideally near ambient) before application. 2. Clean and degrease the joint/surface thoroughly; remove old sealant, oil, rust and contaminants. 3. Apply the paste with a caulking gun and follow manufacturer cure times (initial set 10â15 min, full cure ~18 h) before exposing to full operating temperatures. 4. If rapid heat exposure is expected, allow at least the initial cure and follow any manufacturer instructions for heat ramp-up. Conclusion: For reliable sealing and safety, apply High temperature sealant 310ml PYROSEALANT only to a cooled, prepared surface and let it cure properly before running the engine.

High temperature sealant 310ml PYROSEALANT

All products, Covers/

Additional information

Maximum operating temperature [°C]	287

Thermally resistant sealant in the form of a semi-liquid paste that cures to a non-sticky state within 10 to 15 minutes, and completely within 18 hours. Supplied in 310 ml tubes for a caulking gun. It should be used in well-ventilated areas and avoid contact with gasoline or diesel fuel. Material: a mixture of amorphous silica, polydimethylsiloxane (a type of silicone), iron oxide, and a catalyst. Operating temperature: from -59°C to +287°C (temporarily up to +538°C).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
FQ-PS-310	PYRO-SEALANT 310 ml	-	-	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Thermally resistant sealant in the form of a semi-liquid paste that cures to a non-sticky state within 10 to 15 minutes, and completely within 18 hours. Supplied in 310 ml tubes for a caulking gun. It should be used in well-ventilated areas and avoid contact with gasoline or diesel fuel. Material: a mixture of amorphous silica, polydimethylsiloxane (a type of silicone), iron oxide, and a catalyst. Operating temperature: from -59°C to +287°C (temporarily up to +538°C).