Does the GAL compressed air lubricator with BSP female thread, GA series, require a specific oil type or viscosity for optimal operation?

GAL compressed air lubricator with BSP female thread, GA series does not specify a single mandatory oil brand in the provided description, but optimal operation requires using appropriate lubricating oil for pneumatic lubricators: clean, non-detergent mineral or synthetic compressor oils formulated for air line lubrication. Choose a viscosity that ensures stable atomization into an oil mist at typical supply pressures (up to 10 bar) and operating temperatures (â5Â°C to +70Â°C). Common recommendations: - ISO VG 32 (light oil) is frequently used for general pneumatic applications and works well for most ambient temperatures above freezing. - For lower temperatures near â5Â°C, use a slightly lower-viscosity oil or a fluid rated for low-temperature performance to maintain proper flow and atomization. - For high-temperature or heavy-duty applications, ISO VG 46 may be considered, but avoid oils so viscous that they impair misting at the GA seriesâ flow rates. Always use clean, filtered oil and follow any manufacturer instructions or system component requirements (seals, valves, actuators). If in doubt, consult the lubricator or system manufacturer for a recommended oil type and viscosity to match your specific operating conditions and downstream equipment.

Can the GAL compressed air lubricator with BSP female thread, GA series, be installed vertically or only horizontally?

GAL compressed air lubricator with BSP female thread, GA series can be installed both horizontally and vertically. The design includes an internal BSP thread and a mounting bracket/holder for flexible orientation; GA connection sets (L, T, U) support different piping layouts. Ensure correct alignment of the inlet/outlet according to your piping and maintain the specified supply pressure (up to 10 bar) and operating temperature (-5Â°C to +70Â°C). For optimal performance keep the lubricator accessible for maintenance and verify flow capacity matches your system (sizes 200â600).

GAL compressed air lubricator with BSP female thread, GA series

Q: How often should the GAL compressed air lubricator with BSP female thread, GA series, have its oil reservoir refilled?

The GAL compressed air lubricator with BSP female thread, GA series should have its oil reservoir refilled whenever the sight glass/level indicator shows the oil has dropped to the minimum mark or before continuous operation would reach that level. Typical practice for such inline pneumatic lubricators is to check the oil level at regular service intervals (for example weekly or monthly) depending on system duty cycle and consumption; high-flow or continuously operating systems (higher sizes: 400, 600) will require more frequent checks than low-duty installations (sizes 200, 300). Also refill whenever pressure losses, increased friction, or decreased actuator performance suggest inadequate lubrication. Use the manufacturerârecommended lubricant and do not overfill. keep oil between the minimum and maximum marks.

Air preparation elements (FRL), All products/

Additional information

Maximum operating temperature [°C]	70
Minimum operating temperature [°C]	-5

GAL series GA lubricator with internal BSP thread ensures proper lubrication of devices with oil mist in pneumatic installations. The package includes a mounting bracket/holder. GA connection sets (L, T, U shapes) are used for connecting individual components. Size: 200, 300, 400, 600. Supply pressure: up to 10 bar. Operating temperature: from -5°C to +70°C. Connection: BSP 1/8″ to 1″. Flow rate: 2750 l/min – size 200, 5000 l/min – size 300, 8800 l/min – size 400, 14500 l/min – size 600 (at input pressure 6 bar Δp = 1 bar).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AT-GAL200-06	GAL200 Grease Gun 1/8"	-	-	In stock	Enquiry
AT-GAL200-08	GAL200 Grease Gun 1/4"	-	-	In stock	Enquiry
AT-GAL300-08	GAL300 Grease Gun 1/4"	-	-	In stock	Enquiry
AT-GAL300-10	GAL300 3/8 grease gun	-	-	In stock	Enquiry
AT-GAL300-15	GAL300 Grease Gun 1/2"	-	-	In stock	Enquiry
AT-GAL400-10	GAL400 3/8 grease gun	-	-	In stock	Enquiry
AT-GAL400-15	GAL400 Grease Gun 1/2"	-	-	In stock	Enquiry
AT-GAL600-20	GAL600 Grease Gun 3/4"	-	-	In stock	Enquiry
AT-GAL600-25	GAL600 Grease Gun 1	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

GAL series GA lubricator with internal BSP thread ensures proper lubrication of devices with oil mist in pneumatic installations. The package includes a mounting bracket/holder. GA connection sets (L, T, U shapes) are used for connecting individual components. Size: 200, 300, 400, 600. Supply pressure: up to 10 bar. Operating temperature: from -5°C to +70°C. Connection: BSP 1/8″ to 1″. Flow rate: 2750 l/min – size 200, 5000 l/min – size 300, 8800 l/min – size 400, 14500 l/min – size 600 (at input pressure 6 bar Δp = 1 bar).