Is the BANJO bolt with washers with internal thread, type D9 compatible with couplings R13, R14, D12, D17, D5, and D6 at 18 bar working pressure?

Yes. The BANJO bolt with washers with internal thread, type D9 is specified for couplings type R13, R14, D12, D17, D5, D6 and has a working pressure of 18 bar. Given that the product description explicitly lists compatibility with those coupling types and the working pressure matches 18 bar, the BANJO bolt with washers with internal thread, type D9 is compatible with couplings R13, R14, D12, D17, D5, and D6 at 18 bar working pressure.

Can BANJO bolt with washers with internal thread, type D9 be used with couplings R13, R14, D12, D17, D5, D6 at 18 bar?

Yes. The BANJO bolt with washers with internal thread, type D9 Format is specified for couplings type R13, R14, D12, D17, D5, D6 and its working pressure is 18 bar. Made of nickel-plated brass, it is suitable for use with those couplings at 18 bar provided the couplings and connected system are rated for that pressure and installation follows manufacturer torque and sealing instructions.

Can BANJO bolt with washers with internal thread, type D9 safely operate with R13, R14, D12, D17, D5, D6 couplings at 18 bar?

Yes. based on the provided description, a BANJO bolt with washers with internal thread, type D9 for couplings type R13, R14, D12, D17, D5, D6 made of nickel-plated brass with a working pressure of 18 bar can safely operate with those listed couplings at 18 bar, provided the following conditions are met: - Compatibility: The thread form, size and seating surfaces of the BANJO bolt with washers with internal thread, type D9 must match the mating threads and sealing surfaces of couplings R13, R14, D12, D17, D5 and D6 so that a proper mechanical and seal fit is achieved. - Pressure rating alignment: All couplings and connecting components must be rated for at least 18 bar (or higher). If any coupling has a lower working pressure rating, the assembly would not be safe. - Material suitability: Nickel-plated brass construction is acceptable for many hydraulic and fluid applications at 18 bar, but must be compatible with the conveyed media, temperature range and environment (corrosion, galvanic effects). - Proper installation: Correct torque, use of specified washers/seals, and adherence to manufacturer installation instructions are required to avoid leaks or mechanical failure. - Condition and integrity: Components must be undamaged, free of wear, and properly maintained. Replace any deformed or corroded parts. - System factors: Consider dynamic loads, pressure spikes, pulsation, vibration and temperature extremes; these can raise local stresses above nominal 18 bar and may require higher safety margins or different materials. If all the above are satisfiedâmatching thread/seal geometry, all components rated â¥18 bar, material compatibility and correct installationâthen the BANJO bolt with washers with internal thread, type D9 can be used safely with R13, R14, D12, D17, D5 and D6 couplings at 18 bar. For final assurance, verify manufacturer specifications and, if needed, perform pressure testing or consult the supplier/engineer.

BANJO bolt with washers, with female thread, type D9

All products, Banjo fittings/

Additional information

BANJO bolt with washers, with female thread, type D9, for type R13, R14, D12, D17, D5, D6 fittings. Material: nickel-plated brass. Working pressure: 18 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-2409001	Bolt with female for BANJO D9, female / 1/8" BSP male, 2 washers	-	-	In stock	Enquiry
MW-2409002	Bolt with female for BANJO D9, female / 1/4" BSP male, 2 washers	-	-	In stock	Enquiry
MW-2409003	Bolt with female for BANJO D9, female / 3/8" BSP male, 2 washers	-	-	In stock	Enquiry
MW-2409004	Bolt with female for BANJO D9, female / 1/2" BSP male, 2 washers	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

BANJO bolt with washers, with female thread, type D9, for type R13, R14, D12, D17, D5, D6 fittings. Material: nickel-plated brass. Working pressure: 18 bar.