Is the Plug for UHP with GZ, 700 bar, carbon steel, type RC compatible with systems rated up to 1000 bar given its safety factors?

Plug for UHP with GZ, 700 bar, carbon steel, type RC Format: No . it is not advisable to use this plug in systems rated up to 1000 bar. The product is specified with a working pressure of 700 bar with a safety factor of 4, and 1000 bar only with a reduced safety factor of 2.8. Safety factors indicate margin against failure; a lower safety factor at 1000 bar means the design margin is significantly smaller and may not meet required industry or application-specific safety requirements. Unless the system design, applicable codes and risk assessment explicitly permit operation with a 2.8 safety factor for this component, you should not consider it compatible with continuous or critical 1000 bar service. For safe operation at 1000 bar, choose a component rated for 1000 bar at an acceptable safety factor per your standards or consult the manufacturer/engineering assessment before use.

Can Plug for UHP with GZ, 700 bar, carbon steel, type RC be used in systems operating at intermediate pressures between 700 and 1000 bar?

No. Plug for UHP with GZ, 700 bar, carbon steel, type RC Format is rated for a working pressure of 700 bar with a safety factor of 4; the 1000 bar figure applies only under a lower safety factor (2.8). Using this plug in systems operating between 700 and 1000 bar would exceed its primary rated working pressure and reduce the safety margin, so it is not recommended. For intermediate pressures above 700 bar, select a component explicitly rated for that pressure with an adequate safety factor.

Does Plug for UHP with GZ, 700 bar, carbon steel, type RC require special installation for 1000 bar systems?

No. Plug for UHP with GZ, 700 bar, carbon steel, type RC does not require special installation for use in 1000 bar systems beyond standard precautions, provided system design and procedures account for the differing safety factor. The product is specified with a working pressure of 700 bar (safety factor 4) and 1000 bar (safety factor 2.8); this means the same carbon steel, black-galvanized plug can be used at up to 1000 bar but with a lower safety margin. Before using it at 1000 bar you should: - Verify compatibility with the specific system components and operating conditions (temperature, dynamic loads, media). - Ensure threads and mating parts are rated for 1000 bar and properly prepared and torqued to manufacturer recommendations. - Confirm that system safety factors, relief devices, and inspection intervals are acceptable given the reduced safety factor at 1000 bar. - Follow applicable industry standards and any site-specific engineering approvals. If any doubt exists about long-term reliability or marginal conditions, consult the manufacturer or a qualified engineer.

Cap for UHP with male, 700 bar, carbon steel, type RC

All products, UHP adapters and accessories/

Additional information

Material	CS – steel (cast iron)

Cap for UHP adapters with a male thread. Material: carbon steel, black-galvanized. Working pressure: 700 bar (at a safety factor of 4), 1000 bar (at a safety factor of 2.8). Material: carbon steel, black-galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
EU-RC14	Cap 1/4" NPT male, 700 bar	-	700	In stock	0 zł		Enquiry
EU-RC38	Cap 3/8" NPT male, 700 bar	-	700	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Cap for UHP adapters with a male thread. Material: carbon steel, black-galvanized. Working pressure: 700 bar (at a safety factor of 4), 1000 bar (at a safety factor of 2.8). Material: carbon steel, black-galvanized.