Does the DIN 3015 double insert, polyamide, type 301 support continuous use at +180Â°C and intermittent exposure beyond this range?

The DIN 3015 double insert, polyamide, type 301 is specified with an operating temperature range of -40Â°C to +180Â°C. This means it is designed for continuous use up to +180Â°C. Intermittent exposure above +180Â°C is not covered by the given specification and therefore cannot be guaranteed safe or durable; occasional short peaks slightly above the limit might be possible in practice but would risk degradation of the selfâextinguishing polyamide (loss of mechanical properties, dimensional stability or flameâretardant behavior). For any application expecting temperatures beyond +180Â°C (even intermittently), validate with the manufacturer or choose a material rated for higher temperatures to ensure performance and safety.

Can DIN 3015 double insert, polyamide, type 301 resist chemical exposure from hydraulic fluids and cleaning agents used in industry?

DIN 3015 double insert, polyamide, type 301 offers good general chemical resistance typical for polyamide (PA) and its self-extinguishing grades. It will resist many hydraulic fluids (mineral oils, some synthetic oils) and common industrial cleaning agents, especially at moderate temperatures and short exposures. However, polyamide can be attacked by strong acids, strong alkalis, certain solvents (ketones, chlorinated hydrocarbons), and prolonged contact with aggressive fluids or high-temperature exposure (approaching +180Â°C) can degrade properties, swell, or embrittle the material. For critical applications, compatibility must be confirmed with the specific hydraulic fluid or cleaning agent, exposure concentration, temperature and duration-ideally via supplier chemical resistance data or testing.

Is DIN 3015 double insert, polyamide, type 301 suitable for outdoor UV exposure over time?

No. DIN 3015 double insert, polyamide, type 301 is not ideal for prolonged outdoor UV exposure. Why: The insert is made of self-extinguishing polyamide (nylon), with an operating temperature range of â40Â°C to +180Â°C, which indicates good thermal performance. However, standard polyamide grades are susceptible to degradation from long-term ultraviolet (UV) radiation: UV causes surface chalking, embrittlement, loss of mechanical strength and eventual cracking. The product description does not mention UV stabilizers, weathering additives, or an outdoor-rated (UV-resistant) material grade. Implications: Continuous sun exposure will likely reduce the insertâs lifespan and mechanical integrity over months to years, depending on intensity and climate. If the clamp must retain grip, impact resistance or dimensional stability outdoors, untreated polyamide can fail prematurely. Recommendations: - For long-term outdoor/UV-exposed applications, choose an insert specifically specified as UV-stabilized or weather-resistant, or made from materials better suited to UV (e.g., UV-stabilized PA, polyethylene with UV additives, polypropylene with stabilizers, or certain elastomers). - If replacing material is not possible, protect the insert from direct sunlight (covers, housings, coatings, or paints rated for plastics) and inspect periodically for cracking or embrittlement. - Consult the manufacturer for datasheets or UV-aging test results for DIN 3015 double insert, polyamide, type 301 to confirm suitability for your specific environment.

DIN 3015 double insert, polyamide, type 301

All products, Clamps for hydraulic pipes/

Additional information

Material	P – material (plastic)

Two-part insert for clamp DIN 3015 type 301 made according to standard DIN 3015. Standardly features a profiled (grooved) surface for the pipe opening. Insert material: self-extinguishing polyamide. Operating temperature: from -40°C to +180°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TC-PA301-106,4X	DIN3015 double PA insert for 6.4 mm pipes	-	-	In stock	Enquiry
TC-PA301-106X	DIN3015 double PA insert for 6 mm pipes	-	-	In stock	Enquiry
TC-PA301-108X	DIN3015 double PA insert for 8 mm pipes	-	-	In stock	Enquiry
TC-PA301-109,5X	DIN3015 double PA insert for 9.5 mm pipes	-	-	In stock	Enquiry
TC-PA301-110X	DIN3015 double PA insert for 10 mm pipes	-	-	In stock	Enquiry
TC-PA301-112X	DIN3015 double PA pipe support 12 mm	-	-	In stock	Enquiry
TC-PA301-212,7X	DIN3015 double PA insert for 12.7 mm pipes	-	-	In stock	Enquiry
TC-PA301-213,5X	DIN3015 double PA insert for 13.5 mm pipes	-	-	In stock	Enquiry
TC-PA301-214X	DIN3015 double PA insert for 14 mm pipes	-	-	In stock	Enquiry
TC-PA301-215X	DIN3015 double PA insert for 15 mm pipes	-	-	In stock	Enquiry
TC-PA301-216X	DIN3015 double PA insert for 16 mm pipes	-	-	In stock	Enquiry
TC-PA301-217,2X	DIN3015 double PA insert for 17.2 mm pipes	-	-	In stock	Enquiry
TC-PA301-218X	DIN3015 double PA insert for 18 mm pipes	-	-	In stock	Enquiry
TC-PA301-319X	DIN3015 double PA pipe support 19 mm	-	-	In stock	Enquiry
TC-PA301-320X	DIN3015 double PA pipe support 20 mm	-	-	In stock	Enquiry
TC-PA301-321,3X	DIN3015 double PA insert for pipes 21.3 mm	-	-	In stock	Enquiry
TC-PA301-322X	DIN3015 double PA insert for 22 mm pipes	-	-	In stock	Enquiry
TC-PA301-325,4X	DIN3015 double PA insert for pipes 25.4 mm	-	-	In stock	Enquiry
TC-PA301-325X	DIN3015 double PA insert for 25 mm pipes	-	-	In stock	Enquiry
TC-PA301-426,9X	DIN3015 double PA insert for pipes 26.9 mm	-	-	In stock	Enquiry
TC-PA301-428X	DIN3015 double PA insert for 28 mm pipes	-	-	In stock	Enquiry
TC-PA301-430X	DIN3015 double PA insert for 30 mm pipes	-	-	In stock	Enquiry
TC-PA301-532X	DIN3015 double PA pipe support 32 mm	-	-	In stock	Enquiry
TC-PA301-533,7X	DIN3015 double PA insert for pipes 33.7 mm	-	-	In stock	Enquiry
TC-PA301-535X	DIN3015 double PA pipe support 35 mm	-	-	In stock	Enquiry
TC-PA301-538X	DIN3015 double PA insert for 38 mm pipes	-	-	In stock	Enquiry
TC-PA301-540X	DIN3015 double PA insert for 40 mm pipes	-	-	In stock	Enquiry
TC-PA301-542,4X	DIN3015 double PA insert for pipes 42.4 mm	-	-	In stock	Enquiry
TC-PA301-542X	DIN3015 double PA pipe support 42 mm	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Two-part insert for clamp DIN 3015 type 301 made according to standard DIN 3015. Standardly features a profiled (grooved) surface for the pipe opening. Insert material: self-extinguishing polyamide. Operating temperature: from -40°C to +180°C.