Is the BINDING SPIRAL electrical hose protector suitable for outdoor use in prolonged sunlight exposure?

Yes. The BINDING SPIRAL electrical hose protector is suitable for outdoor use with prolonged sunlight exposure. It is made of black polyethylene (PE) and explicitly stated to be resistant to UV radiation, which helps prevent degradation from sunlight. Additionally, its resistance to acids, oils and solvents and an operating temperature range of -30Â°C to +80Â°C make it durable in a variety of outdoor conditions. For maximum longevity, avoid continuous exposure to extreme temperatures near the upper limit and inspect periodically for mechanical wear or abrasion in high-friction environments.

Can BINDING SPIRAL electrical hose protector withstand chemical exposure from oils and solvents over time?

Yes. BINDING SPIRAL electrical hose protector is made from black polyethylene (PE) tape cut from PE pipe, offering resistance to acids, oils, solvents, and UV radiation. Its lightweight, highly flexible design and specified operating temperature range (â30Â°C to +80Â°C) mean it can withstand typical chemical exposure from oils and many solvents over time. However, prolonged contact with aggressive or specialty chemicals outside typical solvent classes, exposure above the temperature limits, or concentrated chemical immersion may reduce lifespan. For critical applications, verify compatibility with the specific chemical, concentration, temperature, and exposure duration.

How do I install the BINDING SPIRAL electrical hose protector on multiple cables at once?

BINDING SPIRAL electrical hose protector is lightweight, flexible tape cut from PE pipe that wraps around cables to protect and bundle them. To install it on multiple cables at once, follow these steps: 1. Prepare cables: align the cables you want to protect in parallel, keeping them straight and free of sharp bends. Secure them temporarily with tape or cable ties at intervals to maintain spacing. 2. Start end: hold the beginning of the BINDING SPIRAL at one end of the cable group. The spiralâs open slit allows you to position it against the bundle without threading each cable. 3. Wrap by spiraling: press the spiralâs inner edge onto the bundle and rotate it around the cables so the spiral winds along the length. Each turn overlaps slightly and grips the bundle thanks to the flexible PE material. Continue until you reach the other end. 4. Adjust and secure: trim the spiral to length if necessary using a sharp knife or cutters. For extra retention at ends or in high-vibration areas, add a small cable tie or a dab of adhesive compatible with polyethylene (note: PE is chemically resistant. mechanical ties are usually preferred). 5. Multiple cables at once: because BINDING SPIRAL is highly flexible and open-slitted, you can wrap fairly large bundles by aligning several cables and spiraling over them in a single pass. For very thick bundles, consider wrapping in parallel runs or use wider diameter spiral sections if available. 6. Environmental considerations: BINDING SPIRAL is resistant to acids, oils, solvents and UV and works from -30Â°C to +80Â°C, so itâs suitable for outdoor or industrial use. Avoid sharp edges on cable entries and ensure adequate strain relief where cables enter equipment. Tips: work on a flat surface for neat alignment; use a second person for long runs; pre-cut lengths if multiple identical bundles are needed.

BINDING SPIRAL electrical hose protector

All products, Covers/

Additional information

Maximum operating temperature [°C]	80
Minimum operating temperature [°C]	-30
Standard length [m]	25, 50

Lightweight, highly flexible cover made from tape cut from PE pipe. Designed for protecting electrical hoses and hoses, as well as bundling them together. Resistant to acids, oils, solvents, and UV radiation. Material: black polyethylene (PE). Operating temperature: from -30°C to +80°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
SF-BINDING-06	BINDING-SPIRAL 6 mm cover	-	-	In stock	Enquiry
SF-BINDING-08	BINDING-SPIRAL 8 mm cover	-	-	In stock	Enquiry
SF-BINDING-10	BINDING-SPIRAL 10 mm cover	-	-	In stock	Enquiry
SF-BINDING-12	BINDING-SPIRAL 12 mm cover	-	-	In stock	Enquiry
SF-BINDING-15	BINDING-SPIRAL 15 mm cover	-	-	In stock	Enquiry
SF-BINDING-20	BINDING-SPIRAL 20 mm cover	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Lightweight, highly flexible cover made from tape cut from PE pipe. Designed for protecting electrical hoses and hoses, as well as bundling them together. Resistant to acids, oils, solvents, and UV radiation. Material: black polyethylene (PE). Operating temperature: from -30°C to +80°C.