Is the Metric male threaded end, 60Â° taper, carbon steel, type SA compatible with textile-reinforced plastic hoses and external steel braid?

Yes. The Metric male threaded end, 60Â° taper, carbon steel, type SA Format is compatible with textile-reinforced plastic hoses with external steel braid. It is specifically designed for low-pressure rubber and non-reinforced and textile-reinforced plastic hoses with external steel braid, and is commonly used in flexible hoses for sanitary fittings, fuel systems, air systems, etc. The carbon steel, galvanized construction suits these applications, provided the hose specifications (pressure rating, inner diameter, and braid type) match the fittingâs dimensions and working pressure.

Can Metric male threaded end, 60Â° taper, carbon steel, type SA be used in sanitary and fuel flexible hose assemblies?

Yes. Metric male threaded end, 60Â° taper, carbon steel, type SA can be used in sanitary and fuel flexible hose assemblies. It is specifically described for low-pressure rubber, non-reinforced and textile-reinforced plastic hoses with external steel braid and is commonly used in flexible hoses for sanitary fittings and fuel systems. Ensure compatibility with operating pressure, fluid type, temperature, sealing requirements and applicable sanitary/fuel standards; verify corrosion resistance (galvanized carbon steel may require additional protection for some sanitary or fuel environments).

Does the Metric male threaded end, 60Â° taper, carbon steel, type SA require specific torque values for installation?

Metric male threaded end, 60Â° taper, carbon steel, type SA Format. does it require specific torque values for installation? Yes. Although the SA type end (external metric thread, 60Â° cone sealing) is primarily designed for low-pressure rubber and non-reinforced or textileâreinforced plastic hoses with external steel braid, correct installation torque is important to ensure a reliable cone seal and to avoid damage. Recommended practice: - Use manufacturerâspecified torque values when available. These take into account thread size, material (carbon steel, galvanized), and sealing geometry. - If manufacturer data are not provided, follow standard torque guidelines for metric male threads of the given diameter and pitch, adjusted for carbon steel and zinc galvanizing (galvanized coatings can alter friction). Apply conservative torque and tighten incrementally. - Ensure proper lubrication or antiâseize treatment only if specified; lubrication lowers friction and requires lower torque to achieve the same clamp load. - Avoid overâtorquing: excessive torque can deform the 60Â° cone, damage threads, crush plastic hose ends or compromise the sealing surface, leading to leaks. - Use a calibrated torque wrench and tighten to a controlled value; if a final leak test is required, perform pressure testing after assembly. In summary: yes. specific torque values or adherence to standard torque tables and correct installation procedure are required to ensure seal integrity and avoid damage. When possible, obtain and follow the supplier/manufacturerâs exact torque recommendations for the Metric male threaded end, 60Â° taper, carbon steel, type SA Format.

Metric male threaded end, 60° taper, carbon steel, type SA

All products, Low-pressure fittings and adapters/

Additional information

Material	CS – steel (cast iron)

SA type end with external metric thread, 60° cone sealing, designed for low-pressure rubber and non-reinforced and textile-reinforced plastic hoses, with external steel braid. Commonly used in flexible hoses for sanitary fittings, fuel systems, air systems, etc. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
EC-110005	SA GZ M10x1 end, 60° cone, (hose 5.5 mm)	5	30	In stock	Enquiry
EC-110006	SA GZ M12x1.5 end, 60° cone, (hose 5.5 mm)	6	30	In stock	Enquiry
EC-110008	SA GZ M14x1.5 end, 60° cone, (hose 7.5 mm)	8	30	In stock	Enquiry
EC-110010	SA GZ M16x1.5 end, 60° cone, (hose 9 mm)	10	30	In stock	Enquiry
EC-110012	SA GZ M18x1.5 end, 60° cone, (hose 11.5 mm)	12	30	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

SA type end with external metric thread, 60° cone sealing, designed for low-pressure rubber and non-reinforced and textile-reinforced plastic hoses, with external steel braid. Commonly used in flexible hoses for sanitary fittings, fuel systems, air systems, etc. Material: carbon steel, galvanized.