Can UHP hydraulic hose end carbon steel, type PBZ130 be sealed on BSPT threads with Teflon tape or liquid sealant without compromising the crimped thermoplastic hose?

Yes . UHP hydraulic hose end carbon steel, type PBZ130 can be sealed on BSPT threads with PTFE (Teflon) tape or a compatible thread sealant, provided you follow these precautions to avoid compromising the crimped thermoplastic hose: - Apply sealant only to the male BSPT threads. Do not allow tape or liquid sealant to migrate into the bore or over the âtailâ (the special thermoplastic hose sealing/crimping area). - Use minimal, properly applied PTFE tape (wrap in the direction of thread engagement) or a non-curing, petroleum-free thread sealant rated for hydraulic service. Avoid thick layers that could squeeze into the fitting under assembly torque. - Prevent excess sealant from extruding past the thread face when tightening; wipe away any surplus immediately. - During assembly, support the hose and crimped sleeve to avoid axial loads or twisting that could disturb the crimp joint. - After assembly, inspect visually for sealant contamination near the crimp and, if possible, pressure-test the assembly per hose/fitting manufacturer recommendations. Following these steps will allow BSPT thread sealing without compromising the crimped UHP thermoplastic hose integrity.

Does using Teflon tape or liquid sealant on BSPT threads risk damaging the crimped UHP hydraulic hose end carbon steel, type PBZ130?

Using Teflon tape or liquid thread sealant on BSPT threads of UHP hydraulic hose end carbon steel, type PBZ130 can be acceptable for sealing the pipe thread, but care is needed to avoid damaging the crimped hose end. BSPT is a tapered, thread-sealing connection-PTFE tape or appropriate anaerobic/sealing compounds are commonly used. Risks: excess tape or sealant can enter the bore and contaminate the hose assembly or system, interfere with correct engagement of the threads, or create uneven seating that stresses the crimped joint. Aggressive solvents or sealants incompatible with the hose or zinc galvanizing may corrode or weaken the carbon steel finish. Recommendation: use a minimal, even wrap of PTFE tape or a manufacturer-approved liquid sealant compatible with galvanised carbon steel and the hose materials; keep tape/sealant clear of the crimped area and inner bore. When in doubt follow the hose and fitting manufacturerâs instructions for PBZ130.

Is Teflon tape or liquid sealant suitable for sealing BSPT threads on UHP hydraulic hose end carbon steel, type PBZ130?

Yes. Teflon tape or liquid thread sealant can be used to seal the external BSPT thread on the UHP hydraulic hose end carbon steel, type PBZ130, but with important caveats. Key points: - BSPT is a BSP tapered thread that seals primarily on the thread form (metal-to-metal). Applying PTFE (Teflon) tape or a suitable anaerobic/semi-permanent liquid sealant can improve sealing and help prevent leakage, but they must be compatible with the hydraulic fluid, operating pressure, and temperature of the UHP system. - Use a high-quality PTFE tape rated for hydraulic service (suitable thickness, standardized for pipe threads) and wrap in the threadâs tightening direction, avoiding over-application that can alter fit or block ports. - If using liquid thread sealant, select one specified for high-pressure hydraulic applications and compatible with carbon steel and the hydraulic fluid (e.g., petroleum, synthetic, or water-glycol). Ensure the sealant cures appropriately for the thread type and wonât creep into the hose or system. - Beware of contamination: excess tape fragments or uncured sealant can enter the hydraulic system and damage valves or componentsâclean threads before assembly and remove loose particles. - Assembly practice: follow recommended torque values for BSPT on the PBZ130 to achieve proper metal-to-metal contact; thread sealant is supplementary, not a substitute for correct tightening and correct fitting design. - For UHP (ultra-high pressure) service, verify manufacturer recommendations for the PBZ130. Some UHP fittings require specific sealing methods, and manufacturer guidance or certified procedures should take precedence. Recommendation: Confirm with the PBZ130 manufacturer or supplier the approved sealing method and compatible sealants for your hydraulic fluid and pressure. If manufacturer approval is not available, use a hydraulic-grade PTFE tape or a high-pressure pipe thread sealant explicitly rated for BSPT and UHP hydraulic systems, apply carefully, and follow proper assembly and cleanliness procedures.

A fitting hydraulic for hose UHP steel carbon, type PBZ130

Additional information

Material	CS – steel (cast iron)

A hydraulic fitting (type P – with a special “tail” for a thermoplastic hose) with a BSPT male thread, sealing on the thread using tape PTFE or sealant in flows. Intended for crimping in UHP thermoplastic hoses by means of a clamping ferrule appropriate for the hose type. Material: steel carbon, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
TI-PBZ130-06-04-TO	Fitting 3/8" BSPT male, hose thermoplastic 1/4"	6	800	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

A hydraulic fitting (type P – with a special “tail” for a thermoplastic hose) with a BSPT male thread, sealing on the thread using tape PTFE or sealant in flows. Intended for crimping in UHP thermoplastic hoses by means of a clamping ferrule appropriate for the hose type. Material: steel carbon, galvanized.