How do I clean and sterilize the Miniature full-circuit clamp CAW, stainless steel for hygienic environments?

To clean and sterilize the Miniature full-circuit clamp CAW, stainless steel for hygienic environments: 1. Disassemble if possible and remove visible debris. 2. Pre-rinse with warm potable water to remove loose contaminants. 3. Clean with a neutral pH detergent (no chlorides) or a mild alkaline cleaner compatible with AISI 304; use a soft brush or cloth to clean the smooth inner surface and rounded edges-avoid abrasive tools that can scratch. 4. Rinse thoroughly with potable water to remove all detergent residues. 5. Sanitize using an approved food/medical-grade sanitizer (e.g., hot water >80Â°C for thermal sanitization, or a compatible chemical sanitizer such as peracetic acid or a quaternary ammonium compound at manufacturer-recommended concentrations). Ensure compatibility with AISI 304. 6. Rinse again if required by the sanitizerâs instructions. 7. Dry completely or allow to air-dry in a clean environment to prevent corrosion spots. 8. Inspect for residues or damage before reuse; reassemble and install lightweight PVC or rubber hoses as intended. Follow your facilityâs validation procedures and sanitizer manufacturer guidance to ensure effective sterilization.

What are the temperature limits for using the Miniature full-circuit clamp CAW, stainless steel?

The product description for the Miniature full-circuit clamp CAW, stainless steel (AISI 304) does not explicitly state specific temperature limits. However, based on the material AISI 304 stainless steel, typical usable temperature range is approximately -196Â°C (cryogenic) up to about 870Â°C for intermittent service and up to about 600â700Â°C for continuous service without significant loss of mechanical properties or corrosion resistance. For applications involving food, medical, electronic, automotive, or welding equipment where temperature extremes, thermal cycling, or specific regulatory requirements apply, verify exact limits with the manufacturer or supplier before use.

Miniature full-circuit clamp CAW, stainless steel

Q: Is the Miniature full-circuit clamp CAW, stainless steel suitable for use in food and medical applications?

Yes. The Miniature full-circuit clamp CAW, stainless steel is suitable for use in food and medical applications. It is manufactured from AISI 304 stainless steel (W4), a material widely accepted for those industries due to its corrosion resistance and hygienic properties. The clampâs smooth inner surface and full circumference without gaps.made from a single piece of material with rounded edges.minimize crevices where contaminants could accumulate and reduce risk of hose damage, supporting cleanliness and product integrity. Its design for quick, repeatable assembly also suits serial production environments common in food and medical device manufacturing.

All products, Clamps for mounting ends/

Additional information

Material	SS – stainless steel

Clamp with a smooth inner surface, with a full circumference, without gaps, made from a single piece of material. Rounded edges protect the hose from damage. Designed for the installation of lightweight PVC and rubber hoses. Particularly recommended for the serial production of flexible conduits due to easy and quick assembly. Made of AISI 304 stainless steel (W4), allowing use in the food, medical, electronic, automotive, and welding equipment industries. Material: AISI 304 steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
CL-CAW-070	CAW band 5.7÷7.0 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-080	CAW band 6.8÷8.0 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-087	CAW band 7.0÷8.7 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-090	CAW band 7.3÷9.0 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-095	CAW band 7.8÷9.5 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-100	CAW band 8.3÷10.0 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-105	CAW band 8.8÷10.5 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-109	CAW band 9.2÷10.9 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-113	CAW band 9.6÷11.3 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-118	CAW band 10.1÷11.8 mm, width 5 mm, W4	-	-	In stock	Enquiry
CL-CAW-119	CAW band 9.4÷11.9 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-123	CAW band 9.8÷12.3 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-128	CAW band 10.3÷12.8 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-133	CAW band 10.8÷13.3 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-138	CAW band 11.3÷13.8 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-140	CAW band 11.5÷14.0 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-142	CAW band 11.7÷14.2 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-145	CAW band 12.0÷14.5 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-148	CAW band 12.3÷14.8 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-153	CAW band 12.8÷15.3 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-157	CAW band 13.2÷15.7 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-160	CAW band 13.5÷16.0 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-162	CAW band 13.7÷16.2 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-166	CAW band 14.1÷16.6 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-168	CAW band 14.3÷16.8 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-170	CAW band 14.5÷17.0 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-175	CAW band 15.0÷17.5 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-178	CAW band 14.6÷17.8 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-180	CAW band 14.8÷18.0 mm, width 7 mm, W4	-	-	In stock	Enquiry
CL-CAW-185	CAW band 15.3÷18.5 mm, width 7 mm, W4	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Clamp with a smooth inner surface, with a full circumference, without gaps, made from a single piece of material. Rounded edges protect the hose from damage. Designed for the installation of lightweight PVC and rubber hoses. Particularly recommended for the serial production of flexible conduits due to easy and quick assembly. Made of AISI 304 stainless steel (W4), allowing use in the food, medical, electronic, automotive, and welding equipment industries. Material: AISI 304 steel.