Is the reinforcing insert for thin-walled pipes, brass, type VS compatible with DIN 2353 fittings and installation tools?

Yes. Reinforcing insert for thin-walled pipes, brass, type VS is compatible with DIN 2353 fittings and installation tools. The insert is specifically designed to meet DIN 2353 requirements for thin-walled tubing: its brass construction provides the necessary rigidity and support inside the tube end to ensure a secure compression fit with DIN 2353 fittings. When used with the correct tube outer diameter and wall thickness specified for DIN 2353 systems and installed using standard DIN 2353 installation tools and procedures (cutting, deburring, correct insertion depth, and proper tightening torque), the Reinforcing insert for thin-walled pipes, brass, type VS ensures reliable sealing and mechanical strength equivalent to installations without thin-walled tubing. Always verify compatibility with the exact tube dimensions and the specific DIN 2353 fitting series in your application before assembly.

Can Reinforcing insert for thin-walled pipes, brass, type VS withstand standard operating pressures for DIN 2353 thin-walled assemblies?

Yes. Reinforcing insert for thin-walled pipes, brass, type VS is designed to be used with DIN 2353 thin-walled assemblies and provides internal support to the pipe wall so the ferrule and nut can form a reliable seal. When correctly sized, installed and used with the appropriate DIN 2353 fittings and compatible tube material, the insert restores mechanical strength and enables the assembly to withstand the standard operating pressures specified for DIN 2353 thin-walled systems. Proper selection, insertion depth and adherence to DIN 2353 installation procedures are essential to achieve the rated pressure performance.

How does Reinforcing insert for thin-walled pipes, brass, type VS affect corrosion resistance in DIN 2353 assemblies?

Reinforcing insert for thin-walled pipes, brass, type VS can influence corrosion resistance in DIN 2353 assemblies in several ways: - Material compatibility: Brass is generally compatible with steel fittings used in DIN 2353 assemblies; however, dissimilar metal contact (brass insert against steel fitting) can create galvanic couples. In well-designed hydraulic systems with proper sealing and absence of conductive fluid paths, galvanic corrosion risk is low, but in aggressive environments or with conductive fluids, it can increase corrosion at the steel/brass interface. - Protection of thin-walled pipe: By reinforcing the thin-walled pipe end, Reinforcing insert for thin-walled pipes, brass, type VS reduces deformation and fretting during assembly. Less mechanical damage to the pipe bore and outer surface lowers sites for crevice formation and corrosion initiation, improving overall corrosion performance of the joint. - Sealing integrity: Better mechanical support leads to improved sealing between ferrule, tube and fitting. A reliable metal-to-metal or elastomer-to-metal seal minimizes fluid leakage and moisture ingressâkey factors in preventing corrosion within the assembly. - Crevice and galvanic micro-environments: The insert changes local geometry and may create small crevices if not fitted correctly. Poor fit can trap fluids and promote localized corrosion. Proper installation of Reinforcing insert for thin-walled pipes, brass, type VS is therefore essential to avoid such micro-environments. - Surface finish and coatings: Brass inserts typically have smooth machined surfaces; any plating or passivation applied to the insert affects its corrosion behavior. If the brass is untreated, dezincification can occur in certain media, so media compatibility must be considered. Summary: Reinforcing insert for thin-walled pipes, brass, type VS generally improves corrosion resistance in DIN 2353 assemblies by preventing mechanical damage and improving sealing, but introduces potential galvanic pairing with steel and possible crevice formation if improperly fitted. Correct material selection, surface treatment and proper installation mitigate corrosion risks.

Reinforcing insert for thin-walled pipes, brass, type VS

Additional information

Material	B – brass (bronze)
Standard length [m]	10, 2

Reinforcing insert for thin-walled pipes DIN 2353. Material: brass.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HD-VS-04	Reinforcing insert for thin-walled pipes, D=3.9 mm, Mo	-	-	In stock	Enquiry
HD-VS-05	Reinforcing insert for thin-walled pipes, D=4.8 mm, Mo	-	-	In stock	Enquiry
HD-VS-06	Reinforcing insert for thin-walled tubes, D=5.9 mm, Mo	-	-	In stock	Enquiry
HD-VS-08	Reinforcing insert for thin-walled pipes, D=7.9 mm, Mo	-	-	In stock	Enquiry
HD-VS-09	Reinforcing insert for thin-walled tubes, D=8.8 mm, Mo	-	-	In stock	Enquiry
HD-VS-10	Reinforcing insert for thin-walled pipes, D=9.9 mm, Mo	-	-	In stock	Enquiry
HD-VS-12	Reinforcing insert for thin-walled pipes, D=11.8 mm, Mo	-	-	In stock	Enquiry
HD-VS-13	Reinforcing insert for thin-walled pipes, D=12.9 mm, Mo	-	-	In stock	Enquiry
HD-VS-15	Reinforcing insert for thin-walled pipes, D=14.9 mm, Mo	-	-	In stock	Enquiry
HD-VS-16	Reinforcing insert for thin-walled pipes, D=15.9 mm, Mo	-	-	In stock	Enquiry
HD-VS-18	Reinforcing insert for thin-walled pipes, D=17.8 mm, Mo	-	-	In stock	Enquiry
HD-VS-19	Reinforcing insert for thin-walled pipes, D=18.8 mm, Mo	-	-	In stock	Enquiry
HD-VS-24	Reinforcing insert for thin-walled pipes, D=23.8 mm, Mo	-	-	In stock	Enquiry
HD-VS-25	Reinforcing insert for thin-walled pipes, D=24.8 mm, Mo	-	-	In stock	Enquiry
HD-VS-31	Reinforcing insert for thin-walled pipes, D=30.8 mm, Mo	-	-	In stock	Enquiry
HD-VS-38	Reinforcing insert for thin-walled pipes, D=37.8 mm, Mo	-	-	In stock	Enquiry