Is the Round nozzle for coolant, 1/2" system, LOC-LINEÂ® compatible with 1/4" and 3/8" hose sizes?

Round nozzle for coolant, 1/2" system, LOC-LINEÂ® Format: No . the Round nozzle for coolant described as a 1/2" system is specific to that system size and is not directly compatible with 1/4" or 3/8" hose sizes. The product listing shows the nozzle is available in three distinct sizes (1/4", 3/8", and 1/2"), which indicates each size is made to fit its matching hose diameter. To use the nozzle with 1/4" or 3/8" hose you must choose the corresponding 1/4" or 3/8" version rather than the 1/2" system part.

Can the Round nozzle for coolant, 1/2" system, LOC-LINEÂ® withstand continuous use at higher temperatures up to +76Â°C?

Yes. Round nozzle for coolant, 1/2" system, LOC-LINEÂ® is made of acetal and its specified operating temperature is up to +76Â°C, so it can withstand continuous use at temperatures up to +76Â°C. Ensure working pressure does not exceed the specified limit (up to 2 bar) and monitor for any application-specific chemical exposure or mechanical stress that could affect performance.

How do I attach the Round nozzle for coolant, 1/2" system, LOC-LINEÂ® to existing fittings or adapters?

To attach the Round nozzle for coolant, 1/2" system, LOC-LINEÂ® to existing fittings or adapters, follow these steps: 1. Verify compatibility: The Round nozzle for coolant, 1/2" system, LOC-LINEÂ® is designed for the 1/2" LOC-LINEÂ® system. Ensure your existing fittings or adapters accept 1/2" LOC-LINEÂ® components or use a proper adapter to convert to the 1/2" system. 2. Check material and conditions: The nozzle is made of acetal and rated for working pressure up to 2 bar and temperatures up to +76Â°C. Make sure your coolant pressure and temperature stay within these limits. 3. Prepare the connection: Clean both the nozzleâs socket and the mating fitting or adapter to remove chips, coolant residue, oil, or debris that could prevent a secure fit. 4. Snap-fit assembly: Align the Round nozzle for coolant, 1/2" system, LOC-LINEÂ® with the 1/2" LOC-LINEÂ® fitting or adapter. Push the nozzle onto the fitting firmly until it snaps or seats fully. LOC-LINEÂ® modular nozzles typically use a friction/snap connectionâensure it is fully engaged and canât be pulled off by hand. 5. Use an adapter if needed: If your existing fitting is not a 1/2" LOC-LINEÂ® receiver, obtain a compatible adapter (e.g., threaded or push-fit adapter to 1/2" LOC-LINEÂ®). Screw or install the adapter to your machineâs coolant port per its instructions, then snap the Round nozzle for coolant, 1/2" system, LOC-LINEÂ® onto the adapter. 6. Test the connection: Slowly apply coolant at operating pressure (â¤2 bar) and inspect for leaks or loosening. Check that flow direction and spray pattern are correct and that the nozzle remains securely attached. If you are unsure about adapter sizing or pressure/temperature limits, consult the equipment manual or supplier to select the proper adapter for the 1/2" LOC-LINEÂ® system.

Round nozzle for coolant, 1/2″ system, LOC-LINE®

Air and water hoses, All products/

Additional information

Round nozzle for coolant hoses LOC-LINE® – 1/2″ system. Available in sizes 1/4″, 3/8″, and 1/2″. Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +76°C.

List of product variants

Article number	Product variant name	Nominal inner diameter	Working pressure [bar]
LL-59862	Round nozzle 3/8" (1/2" system)	-	2
LL-59863	Round nozzle 1/2" (1/2" system)	-	2
LL-59866	Round nozzle 1/4" (1/2" system)	-	2

Round nozzle for coolant hoses LOC-LINE® – 1/2″ system. Available in sizes 1/4″, 3/8″, and 1/2″. Material: acetal. Working pressure: up to 2 bar. Operating temperature: up to +76°C.