Can the Twisted sleeve for 1SN hydraulic hoses, carbon steel, type S1T be used with screwed fittings from other suppliers than TI-S?

No. The Twisted sleeve for 1SN hydraulic hoses, carbon steel, type S1T must be used only with a screwed fitting from the same supplier (TIâS). The product description for the comparable Screwed sleeve for rubber hydraulic hoses type 1SN(R1AT) explicitly states: "Use only with a screwed fitting from the same supplier (TIâS...)." Given identical material (carbon steel, galvanized) and the same compatibility restriction, mixing the S1T twisted sleeve with screwed fittings from other suppliers risks improper fit, leakage, or failure. For safe, reliable connections and to maintain any warranties or specifications, use TIâS screwed fittings designed for the S1T sleeve.

Is the Twisted sleeve for 1SN hydraulic hoses, carbon steel, type S1T compatible with fittings other than TI-S series?

Twisted sleeve for 1SN hydraulic hoses, carbon steel, type S1T Format: According to the product description for the screwed sleeve for rubber hydraulic hoses type 1SN(R1AT), the sleeve is intended to be used only with a screwed fitting from the same supplier (TI-S series). Therefore the Twisted sleeve for 1SN hydraulic hoses, carbon steel, type S1T Format is not compatible with fittings other than the TI-S series.

Are there any warranty or safety restrictions when using Twisted sleeve for 1SN hydraulic hoses, carbon steel, type S1T with non-TI-S fittings?

Yes. there are warranty and safety restrictions. Explanation: The Screwed sleeve for rubber hydraulic hoses type 1SN(R1AT) is specified for use only with a screwed fitting from the same supplier (TI-S...) and is made of carbon steel, galvanized. By analogy, Twisted sleeve for 1SN hydraulic hoses, carbon steel, type S1T Format used with non-TI-S fittings would violate the supplierâs specified usage. Using a sleeve with fittings not supplied/designed by the same manufacturer can invalidate warranties and create safety risks (leakage, fitting blow-off, premature wear or failure) because compatibility, thread fit, material, and assembly tolerances are not guaranteed. Practical implications: - Warranty: Manufacturer likely voids warranty if non-TI-S fittings are used. - Safety: Increased risk of hydraulic failure due to incompatible components; possible pressure loss or hazardous disconnection. - Compliance: May breach supplier instructions and industry best practices; could affect liability and insurance. Recommendation: Use Twisted sleeve for 1SN hydraulic hoses, carbon steel, type S1T Format only with the matching TI-S screwed fittings from the same supplier or obtain written confirmation from the manufacturer that specific non-TI-S fittings are acceptable.

Screw-together ferrule for hoses hydraulic 1SN, carbon steel, type S1T

All products, Fittings for high-pressure hoses/

Additional information

Material	CS – steel (cast iron)

Screw-together ferrule for non-skive rubber hydraulic hoses type 1SN(R1AT). Use only with fittings screw-together from the same supplier (TI-S…). Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-S1T-03	Sleeve na hose SAE R1AT DIN 20022 3/16"	5	-	In stock	Enquiry
TI-S1T-04	Sleeve na hose SAE R1AT DIN 20022 1/4"	6	-	In stock	Enquiry
TI-S1T-05	Sleeve na hose SAE R1AT DIN 20022 5/16"	8	-	In stock	Enquiry
TI-S1T-06	Sleeve na hose SAE R1AT DIN 20022 3/8"	10	-	In stock	Enquiry
TI-S1T-08	Sleeve na hose SAE R1AT DIN 20022 1/2"	12	-	In stock	Enquiry
TI-S1T-10	Sleeve na hose SAE R1AT DIN 20022 5/8"	16	-	In stock	Enquiry
TI-S1T-12	Sleeve na hose SAE R1AT DIN 20022 3/4"	20	-	In stock	Enquiry
TI-S1T-16	Sleeve na hose SAE R1AT DIN 20022 1"	25	-	In stock	Enquiry
TI-S1T-20	Sleeve na hose SAE R1AT DIN 20022 1.1/4"	32	-	In stock	Enquiry
TI-S1T-24	Sleeve na hose SAE R1AT DIN 20022 1.1/2"	38	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Screw-together ferrule for non-skive rubber hydraulic hoses type 1SN(R1AT). Use only with fittings screw-together from the same supplier (TI-S…). Material: carbon steel, galvanized.