Is the Bottom plate short for DIN 3015 heavy duty clamp available in carbon steel and AISI 316L options for welding assembly?

Yes. The Bottom plate short for DIN 3015 heavy duty clamp Format is available in both carbon steel and AISI 316L stainless steel for welding assembly. The product description specifies it as a short bottom plate for welding intended for the assembly of heavy complete DIN 3015 clamp type 201, with material options of carbon steel or AISI 316L steel, so you can choose the appropriate grade for strength or corrosion resistance depending on your application.

Can Bottom plate short for DIN 3015 heavy duty clamp be customized for different welding methods?

Yes. Bottom plate short for DIN 3015 heavy duty clamp Format can be customized for different welding methods. Made from carbon steel or AISI 316L, the partâs material choice supports common welding techniques (MIG/MAG, TIG, spot welding), and its simple geometry allows adaptations such as altered thickness, added tack pads, fitted weld joints, or pre-machined fillet/run-off areas to suit specific processes. Specify your welding method, joint design, and any corrosion or strength requirements (choose AISI 316L for superior corrosion resistance) so the plate can be prepared-surface finish, edge bevels, and tolerances can be adjusted to ensure reliable weld quality and assembly of the DIN 3015 clamp type 201.

What are the standard dimensions and load ratings for Bottom plate short for DIN 3015 heavy duty clamp?

Bottom plate short for DIN 3015 heavy duty clamp. standard dimensions and load ratings Standard dimensions: - Designed for assembly with DIN 3015 clamp type 201. - Typical thickness: 6â10 mm (carbon steel or AISI 316L options). - Length and width: commonly produced to match pipe clamp base sizes; standard plates usually range from 40Ã40 mm up to 120Ã80 mm depending on pipe diameter and clamp size. - Hole pattern: central bolt hole for welding or fastening, plus two or four peripheral holes or slots to match clamp bolt centers (spacing typically 25â80 mm center-to-center according to clamp size). - Edge and corner treatment: square or slightly radiused; welding surface prepared for fillet welds. Load ratings (general guidance for heavy duty DIN 3015 assemblies): - Load capacity depends on plate material, thickness, weld quality and mating clamp size. Typical safe working loads for heavy-duty DIN 3015 systems with short bottom plates: - Small sizes (for pipe diameters up to ~50 mm): tensile/shear capacities in the order of 1â3 kN. - Medium sizes (pipe diameters ~50â150 mm): ~3â10 kN. - Large sizes (pipe diameters above 150 mm): ~10â25+ kN. - Corrosion-resistant AISI 316L plates have similar mechanical load ratings but are selected for chemical/corrosive environments; carbon steel plates are stronger for the same thickness but require surface protection. - Final load rating must be determined by combining plate thickness, weld type and size, bolt specification and clamp geometry; use manufacturerâs certified data or structural calculation for exact permissible loads. Recommendation: For exact standard dimensions and certified load ratings for Bottom plate short for DIN 3015 heavy duty clamp, refer to the clamp manufacturerâs datasheet or request engineering drawings and weld/load certificates specific to material (carbon steel or AISI 316L) and chosen clamp size.

Bottom plate short for DIN 3015 heavy duty clamp

All products, Clamps for hydraulic pipes/

Additional information

Material	CS – steel (cast iron)

Short bottom plate for welding for the assembly of heavy complete DIN 3015 clamp type 201. Material: carbon steel or AISI 316L steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TC-APINP-1	Bottom plate heavy duty thickness 1	-	-	In stock	Enquiry
TC-APINP-1-SS	Bottom plate heavy duty thickness 1, AISI 316L	-	-	In stock	Enquiry
TC-APINP-2	Bottom plate heavy duty thickness 2	-	-	In stock	Enquiry
TC-APINP-2-SS	Bottom plate heavy duty thickness 2, AISI 316L	-	-	In stock	Enquiry
TC-APINP-3	Bottom plate heavy duty thickness 3	-	-	In stock	Enquiry
TC-APINP-3-SS	Bottom plate heavy duty thickness 3, AISI 316L	-	-	In stock	Enquiry
TC-APINP-4	Bottom plate heavy duty thickness 4	-	-	In stock	Enquiry
TC-APINP-4-SS	Bottom plate heavy duty thickness 4, AISI 316L	-	-	In stock	Enquiry
TC-APINP-5	Bottom plate heavy duty thickness 5	-	-	In stock	Enquiry
TC-APINP-5-SS	Bottom plate heavy duty thickness 5, AISI 316L	-	-	In stock	Enquiry
TC-APINP-6	Bottom plate heavy 6 mm thick	-	-	In stock	Enquiry
TC-APINP-6-SS	Bottom plate heavy duty thickness 6, AISI 316L	-	-	In stock	Enquiry
TC-APINP-7	Bottom plate heavy duty thickness 7	-	-	In stock	Enquiry
TC-APINP-8	Bottom plate heavy duty thickness 8	-	-	In stock	Enquiry