Is the SMS end under nut with tail under RS clamp, stainless steel, type SWR suitable for food industry use at up to 15 bar with Ra 0.8 Âµm in the hole?

Yes. The SMS end under nut with tail under RS clamp, stainless steel, type SWR Format described is suitable for food industry use up to 15 bar with Ra 0.8 Âµm in the hole, provided these conditions are met: - Surface finish: Ra 0.8 Âµm in the bore meets common hygienic requirements for food contact applications (minimizes bacterial retention). - Material: Stainless steel construction is appropriate for food environments; verify specific grade (e.g., AISI 304 or 316) to ensure corrosion resistance for your product and cleaning agents. - Pressure rating: The couplingâs maximum allowable working pressure of 15 bar covers your stated pressure requirement. - Gasket compatibility: Operating temperature and chemical compatibility depend on gasket material . select a food-grade gasket (e.g., EPDM, PTFE, or FDA-compliant elastomer) rated for your process temperature and media. - Cleanability and assembly: Ensure correct installation with RS clamp and proper sanitary assembly practices to maintain hygienic integrity. - Compliance: Confirm conformity with applicable food-contact standards (e.g., FDA, EC 1935/2004, or local regulations) and any required traceability/certification. If stainless grade and gasket selection are appropriate and regulatory requirements are met, the SMS end under nut with tail under RS clamp, stainless steel, type SWR Format is suitable for food industry use up to 15 bar with Ra 0.8 Âµm.

Can SMS end under nut with tail under RS clamp, stainless steel, type SWR meet food industry hygiene requirements with Ra 0.8 Âµm at â¤15 bar?

Yes - SMS end under nut with tail under RS clamp, stainless steel, type SWR Format can meet foodâindustry hygiene requirements if the specified surface finish and construction are respected. With Ra 0.8 Âµm measured in the bore, stainless steel construction, and gasket materials appropriate for food use and temperature, the fitting provides a hygienic smooth surface. The couplingâs maximum allowable working pressure of 15 bar is acceptable for many food processing applications; ensure gasket selection and clamp assembly are rated for the intended temperature and pressure. Also verify proper cleaning/accessibility, correct sealing (foodâgrade gasket), and documentation/certification for food contact to fully comply with regulatory and customer hygiene standards.

Can SMS end under nut with tail under RS clamp, stainless steel, type SWR be used in food applications with Ra 0.8 Âµm and 15 bar?

Yes. SMS end under nut with tail under RS clamp, stainless steel, type SWR Format can be used in food applications as described, provided the following conditions are met: - Surface finish: Ra 0.8 Âµm (in the hole) is acceptable for many food industry applications; it supports hygienic cleaning and limits bacterial retention. Confirm this meets your specific regulatory or client requirements (some sectors demand Ra â¤ 0.8 Âµm or electropolished surfaces). - Pressure rating: The couplingâs maximum allowable working pressure of 15 bar is acceptable if system operating pressure does not exceed this value and pressure/temperature combinations stay within the gasket and material ratings. - Material: Stainless steel construction is appropriate for food contact; verify the specific stainless grade (e.g., 316L preferred) for corrosion resistance and regulatory acceptance. - Gasket: Operating temperature depends on gasket materialâchoose a food-grade gasket (e.g., FDA-compliant EPDM, FKM, PTFE) rated for your process temperature and compatible with product and cleaning agents. - Cleanability & design: Ensure the tail, clamp and under-nut geometry do not create crevices that impede cleaning. Proper assembly with RS clamp and selected gasket should maintain hygienic integrity. - Validation & compliance: Verify compliance with applicable food safety standards (e.g., FDA, EU regulations, EHEDG, 3-A) and perform hygienic validation (cleaning, pressure/leak tests) per facility protocols. If all the above are satisfied. appropriate stainless grade, food-grade gasket chosen for operating temperature, system pressure â¤15 bar, and hygienic validation performed. the SMS end under nut with tail under RS clamp, stainless steel, type SWR Format is suitable for food applications.

SMS end under nut with tail under RS clamp, stainless steel, type SWR

All products, Hygienic stainless steel couplings/

Additional information

Material	SS – stainless steel
Standard length [m]	100

SMS end fitting under cap, with tail under RS clamp, Ra (in the hole) 0.8 µm, for use in the food industry. Maximum allowable working pressure (for the coupling itself): 15 bar. Operating temperature: depending on the type of material used for the gasket. Material: stainless steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
NH-SWR-025	End. SMS under RS DN25, hose 25 mm	25	15	In stock	Enquiry
NH-SWR-032	End. SMS under RS DN32, hose 32 mm	32	15	In stock	Enquiry
NH-SWR-038	End. SMS under the RS DN38 clamp, hose 38 mm	38	15	In stock	Enquiry
NH-SWR-050	End. SMS under RS DN50, hose 50 mm	50	15	In stock	Enquiry
NH-SWR-051	End. SMS under RS DN50, hose 51 mm	50	15	In stock	Enquiry
NH-SWR-063	End. SMS under RS DN63, hose 63 mm	65	15	In stock	Enquiry
NH-SWR-075	End. SMS under the RS DN75 sleeve, hose 75 mm	75	15	In stock	Enquiry
NH-SWR-076	End. SMS under the RS DN75 sleeve, hose 76 mm	75	15	In stock	Enquiry
NH-SWR-102	End. SMS under RS DN100, hose 102 mm	100	15	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

SMS end fitting under cap, with tail under RS clamp, Ra (in the hole) 0.8 µm, for use in the food industry. Maximum allowable working pressure (for the coupling itself): 15 bar. Operating temperature: depending on the type of material used for the gasket. Material: stainless steel.