Is the Twisted quadrant for pneumatic hoses, type C11 compatible with soft plastic hoses requiring Ni-plated brass fittings and rated for 18 bar working pressure?

Yes. The Twisted quadrant for pneumatic hoses, type C11 is compatible with soft plastic hoses that require nickelâplated brass fittings and are rated for 18 bar working pressure. The Type C11 fourâway connector is specifically designed for connecting hoses made of soft plastics, uses nickelâplated brass material, and is rated to 18 bar working pressure.matching the hose requirements.

Can Twisted quadrant for pneumatic hoses, type C11 four-way connector be used with soft-plastic hoses at 18 bar?

Yes. Twisted quadrant for pneumatic hoses, type C11 four-way connector is specifically designed for connecting hoses made of soft plastics and its working pressure is rated at 18 bar. The connection method-pushing the hose onto the fitting and tightening with the nut-suits soft-plastic hoses when properly installed. Ensure hoses and fittings are compatible in diameter, the nut is fully tightened, and inspect for leaks or deformation under pressure before full operation.

Can Twisted quadrant for pneumatic hoses, type C11 four-way connector securely join soft-plastic hoses at 18 bar?

Yes. Twisted quadrant for pneumatic hoses, type C11 four-way connector can securely join softâplastic hoses at 18 bar, provided a few conditions are met. The connector is specified for hoses made of soft plastics and a working pressure of 18 bar; its connection method (push-on hose with a screw-on nut) and nickelâplated brass construction are appropriate for creating a reliable mechanical and pressure-tight joint at that rated pressure. Key conditions to ensure secure performance: - Hose compatibility: use hoses rated for â¥18 bar and with an outer diameter matching the fitting size intended for the C11 connector. Softâplastic hoses must have sufficient wall thickness and reinforcement if required. - Proper assembly: push the hose fully onto the fitting barb and tighten the nut correctly to compress any internal insert or ferrule (if present) and form the seal. Follow any manufacturer torque/recommendation. - Inspection and testing: after assembly, perform a pressure test at or slightly above working pressure and check for leaks, slippage, or deformation. - Operating factors: avoid sharp bends, external loads, excessive temperature, chemical exposure or vibration that could reduce joint integrity. Use hose clamps or supports if needed. - Maintenance: periodically inspect for wear, nut loosening or hose degradation. If the hose type, diameter, assembly technique and operating conditions conform to these points, Twisted quadrant for pneumatic hoses, type C11 four-way connector will securely join softâplastic hoses at 18 bar.

Twisted quadrant for pneumatic hoses, type C11

All products, Tubular fittings/

Additional information

Material	B – brass (bronze)

Type C11 four-way connector designed for connecting hoses made of soft plastics. The connection is made by pushing the hose onto the fitting and tightening it by screwing on the nut. Material: nickel-plated brass. Working pressure: 18 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-2311001	C11 four-way connector, 4 x hose 6/4	-	16	In stock	Enquiry
MW-2311002	C11 four-way connector, 4 x hose 8/6	-	16	In stock	Enquiry
MW-2311003	Connector four-way C11, 4 x hose 10/8	-	16	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Type C11 four-way connector designed for connecting hoses made of soft plastics. The connection is made by pushing the hose onto the fitting and tightening it by screwing on the nut. Material: nickel-plated brass. Working pressure: 18 bar.