Can the Universal brass ball valve (tap), type 5600, be used outdoors in freezing conditions and how should it be drained to prevent damage?

Universal brass ball valve (tap), type 5600 can be used outdoors, but only if it is protected from freezing liquid. The declared operating temperature range is -20Â°C to +110Â°C; however the minimum temperature applies to the valve emptied of liquid. WARNING in the description states that at negative ambient temperatures the valve must be drained of water to avoid damage (freezing expansion can break seats, seals or the body). How to drain to prevent damage: - Fully open the valve to allow trapped water in the body and hose connection to escape. - Disconnect any attached hose or downstream piping if needed to let all water run out of the aerator and connection. - Tilt or orient the valve so remaining liquid flows out of the lowest ports; remove the aerator or use the hose connection to purge residual water. - Ensure stem area and bore are dry; operate the lever a few times to expel droplets from internal cavities. - Store the valve or installation in a frost-free place or insulate/heat the installation if continuous outdoor use below 0Â°C is required. Materials: nickel-plated brass body, chrome-plated brass ball, PTFE seat and NBR stem O-rings . these will be damaged if frozen while filled. Follow draining and winterization to comply with safe use.

Is the Universal brass ball valve (tap), type 5600, compatible with petrochemical media and chemicals given its material construction?

Universal brass ball valve (tap), type 5600, can be compatible with many petrochemical media and chemicals but only insofar as the media are chemically compatible with its materials: nickel-plated brass body, chrome-plated brass ball, PTFE ball sealing, NBR stem O-rings, aluminum lever and polyamide aerator. It is suitable for water, chemicals and petrochemical products free of solid contaminants, as stated, but compatibility depends on specific chemical aggressiveness, concentration and temperature (operating â20Â°C to +110Â°C). NBR is sensitive to ketones, crude oils, aromatic hydrocarbons and some solvents; brass can suffer dezincification in ammonia, certain acids and saline environments; PTFE is broadly chemical-resistant. For safe use, verify compatibility of each specific petrochemical/chemical (including concentration and operating temperature) with brass, NBR and PTFE; if doubt or with highly aggressive media, choose a valve with resistant materials or consult manufacturer specifications.

What inspection is recommended for the Universal brass ball valve (tap), type 5600, after long-term chemical service?

For Universal brass ball valve (tap), type 5600, after long-term chemical service it is recommended to perform a thorough inspection including: - Visual inspection of body, lever and connections for corrosion, pitting or plating degradation (nickel- and chrome-plating wear). - Check ball and sealing surfaces for chemical attack, scoring, swelling or deposits; disassemble if necessary to inspect chrome-plated ball and PTFE seat condition. - Inspect stem sealing: verify integrity of both NBR O-rings for hardening, cracking or swelling; replace O-rings showing any deterioration. - Verify aerator (polyamide) for embrittlement, cracking or chemical degradation; replace if compromised. - Operate the valve through full travel to confirm smooth action and stem blow-out protection functionality; note increased torque or sticking. - Pressure/leak test at appropriate working pressure and temperature to confirm tightness of ball sealing and stem seals. - Check threads (BSP, ISO 228-1) for damage or chemical-induced degradation and replace or re-seal as required. - Assess suitability of retained materials relative to the chemicals used (per original chemical resistance data); if incompatibility is found, replace the valve. - After inspection/repairs, document findings, parts replaced, and next inspection interval based on chemical aggressiveness and service history. Prioritize replacement of PTFE seats, NBR O-rings and polyamide aerator when signs of chemical degradation are present.

Universal, brass ball valve draw-off (tap), type 5600

All products, Ball valves/

Additional information

Material	B – brass (bronze)

Universal ball valve shut-off draw-off (tap) production European, made with casting, with a lever straight aluminum, with a spigot pod hose and an aerator, intended for installations industrial and water-supply. can be used for water, chemicals, products petrochemical, itp., free od contamination solid, compliant with resistance chemical materials valve. It has stem blow-out protection. Meets the requirements of the pressure directive PED 2014/68/EU, in the scope of sound engineering practice (SEP), in accordance with art. 4 ust. 3 (without markings CE). Compliant with the RoHS 2011/65/EU material directive and the REACH 1907/2006 regulation. Working pressure dependent is od temperature use. The given minimum operating temperature applies to a valve emptied of freezing liquid. Note: W case use na outside, necessary is emptying valve with water at negative temperature ambient! Material the body: brass nickel-plated. Material the ball: brass chrome-plated. Material lever: aluminum. Material aerator: polyamide (PA). sealing the ball: PTFE. sealing stem: 2 x O-ring NBR. connection: thread BSP (ISO 228-1). Operating temperature: from -20°C to +110°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
RV-5600-10	Valve ball draw-off type 5600, 3/8" BSP male, brass, aluminum lever	-	16	In stock	Enquiry
RV-5600-13	Valve ball draw-off type 5600, 1/2" BSP male, brass, aluminum lever	-	16	In stock	Enquiry
RV-5600-19	Valve ball draw-off type 5600, 3/4" BSP male, brass, aluminum lever	-	16	In stock	Enquiry
RV-5600-25	Valve ball draw-off type 5600, 1" BSP male, brass, aluminum lever	-	16	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Universal ball valve shut-off draw-off (tap) production European, made with casting, with a lever straight aluminum, with a spigot pod hose and an aerator, intended for installations industrial and water-supply. can be used for water, chemicals, products petrochemical, itp., free od contamination solid, compliant with resistance chemical materials valve. It has stem blow-out protection. Meets the requirements of the pressure directive PED 2014/68/EU, in the scope of sound engineering practice (SEP), in accordance with art. 4 ust. 3 (without markings CE). Compliant with the RoHS 2011/65/EU material directive and the REACH 1907/2006 regulation. Working pressure dependent is od temperature use. The given minimum operating temperature applies to a valve emptied of freezing liquid. Note: W case use na outside, necessary is emptying valve with water at negative temperature ambient! Material the body: brass nickel-plated. Material the ball: brass chrome-plated. Material lever: aluminum. Material aerator: polyamide (PA). sealing the ball: PTFE. sealing stem: 2 x O-ring NBR. connection: thread BSP (ISO 228-1). Operating temperature: from -20°C to +110°C.