Is the Walterscheidâ¢ WE-MT angle screw connection, carbon steel, compatible with anaerobic thread sealants instead of Teflon tape?

Yes. The Walterscheidâ¢ WE-MT angle screw connection, carbon steel is compatible with anaerobic thread sealants. The product description for the DIN 2353 Eaton Walterscheidâ¢ screw-in angled connector, type WE-MT specifically states the thread seal can be made with Teflon tape or an anaerobic sealant. Use a thread sealant suited for carbon steel and hydraulic applications, follow the sealant manufacturerâs curing and assembly instructions, and ensure proper cleaning of threads before application. Also respect the connectorâs torque and installation procedure to preserve the 24Â° DIN 2353 sealing interface and Guardian Sealâ¢ galvanic coating.

Can the Walterscheidâ¢ WE-MT angle screw connection, carbon steel, be used with PTFE tape without affecting Guardian Sealâ¢ coating?

Yes - Walterscheidâ¢ WE-MT angle screw connection, carbon steel can be used with PTFE (Teflon) tape. The DIN 2353 description explicitly notes the seal on the thread may be achieved âwith Teflon tape or anaerobic sealant.â When applying PTFE tape, use a light, even wrapping technique and avoid excess tape that could shred or migrate into the hydraulic system. The Guardian Sealâ¢ galvanic coating is compatible with typical PTFE tape use; proper application (clean threads, correct tape direction, minimal layers) prevents impairment of the coating and ensures reliable sealing.

Can Walterscheidâ¢ WE-MT angle screw connection, carbon steel withstand repeated assembly with PTFE tape?

Yes. Walterscheidâ¢ WE-MT angle screw connection, carbon steel can withstand repeated assembly with PTFE (Teflon) tape, with some caveats. Key points: - The connector uses a 24Â° DIN 2353 sealing face; the thread is sealed externally (âseal on the thread â with Teflon tape or anaerobic sealantâ), so PTFE tape is an accepted sealing method per the product description. - Carbon steel material with Guardian Sealâ¢ galvanic coating provides corrosion protection and is compatible with common thread sealants including PTFE tape. - Repeated assembly: PTFE tape is suitable for multiple make/break cycles better than some liquid sealants because it is non-curing. However, each re-assembly should use fresh PTFE tape; old tape must be removed completely to ensure reliable sealing and to avoid debris or uneven sealing surfaces. - Practical considerations: avoid over-application of tape (2â3 turns of good-quality tape is typical); ensure tape does not intrude into the 24Â° sealing face or into the hydraulic port; torque to recommended values to preserve the metal sealing surfaces; inspect threads and coating for damage before re-use. - For critical or high-pressure applications, anaerobic (cured) sealants or original manufacturer recommendations may be preferred. If frequent disassembly/reassembly is expected, verify against Eaton/Walterscheid maintenance guidelines or contact Walterscheid support for application-specific advice. Conclusion: Walterscheidâ¢ WE-MT angle screw connection, carbon steel is compatible with PTFE tape and can be reassembled repeatedly when cleaned and resealed properly, following good practice and torque/inspection rules.

Walterscheid™ WE-MT angle screw connection, carbon steel

Additional information

Material	CS – steel (cast iron)

DIN 2353 Eaton Walterscheid™ screw-in angled connector, type WE-MT: 24° DIN 2353 socket with external metric thread and external metric thread (seal on the thread – with Teflon tape or anaerobic sealant). Available as: LL (very light series), L (light series), S (heavy series). Material: carbon steel, with Guardian Seal™ galvanic coating.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HD-WE-04LL-MT-08-W	Walterscheid connector DIN 2353 WE 4LL M8x1	-	100	In stock	Enquiry
HD-WE-06L-MT-10-W	Walterscheid connector DIN 2353 WE 6L M10x1	-	250	In stock	Enquiry
HD-WE-06LL-MT-10-W	Walterscheid connector DIN 2353 WE 6LL M10x1	-	100	In stock	Enquiry
HD-WE-06S-MT-12-W	Walterscheid connector DIN 2353 WE 6S M12x1.5	-	630	In stock	Enquiry
HD-WE-08L-MT-12-W	Walterscheid fitting DIN 2353 WE 8L M12x1.5	-	250	In stock	Enquiry
HD-WE-08LL-MT-10-W	Walterscheid connector DIN 2353 WE 8LL M10x1	-	100	In stock	Enquiry
HD-WE-08S-MT-14-W	Walterscheid fitting DIN 2353 WE 8S M14x1.5	-	630	In stock	Enquiry
HD-WE-10L-MT-14-W	Walterscheid fitting DIN 2353 WE 10L M14x1.5	-	250	In stock	Enquiry
HD-WE-10S-MT-16-W	Walterscheid connector DIN 2353 WE 10S M16x1.5	-	630	In stock	Enquiry
HD-WE-12L-MT-16-W	Walterscheid fitting DIN 2353 WE 12L M16x1.5	-	250	In stock	Enquiry
HD-WE-12S-MT-18-W	Walterscheid fitting DIN 2353 WE 12S M18x1.5	-	630	In stock	Enquiry
HD-WE-15L-MT-18-W	Walterscheid connector DIN 2353 WE 15L M18x1.5	-	250	In stock	Enquiry
HD-WE-16S-MT-22-W	Walterscheid fitting DIN 2353 WE 16S M22x1.5	-	400	In stock	Enquiry
HD-WE-18L-MT-22-W	Walterscheid connector DIN 2353 WE 18L M22x1.5	-	160	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

DIN 2353 Eaton Walterscheid™ screw-in angled connector, type WE-MT: 24° DIN 2353 socket with external metric thread and external metric thread (seal on the thread – with Teflon tape or anaerobic sealant). Available as: LL (very light series), L (light series), S (heavy series). Material: carbon steel, with Guardian Seal™ galvanic coating.